Printer not connecting to computer - orange wifi light stays on

try to put it back to the same place where you took it, if it work, it means that the place where you moved it might have poor signal and if thats the case, i advise you to put a wifi repeater/extender near that wireless printer

Make sure that the firmware of your printer is up to date. Just go to http://bit.ly/ghfW8H to download the firmware update.

If the WiFi light on your printer is orange, re-install the software and connect your printer to your network.

If the WiFi light is green, powercycle your printer, router and computer. After rebooting, assign a static IP on the printer.

The colors of the WiFi indicator light show the network status of the printer.

• Off means one of the following:
• The printer is turned off or is powering up.
• The printer is not connected to a wireless network and in power saver mode. In power saver mode, the power light pulses on and off.
• The printer is connected to an ethernet network. Refer to the Quick Reference Guide to find out if your printer has ethernet capability.
• Solid orange means one of the following:
• The printer has not yet been configured for a wireless network.
• The printer is configured for an ad hoc connection, but it is not currently communicating with another ad hoc device.
• Blinking orange on the WiFi light means one of the following:
• The printer is out of the range of the wireless access point (wireless router).
• The printer is trying to communicate with the wireless access point but the wireless point is turned off or not working properly.
• Either the configured printer of the wireless access point has been turned off and back on, or the printer is trying to establish communications with the network.
• The wireless settings of the printer may no longer be valid.
• Green means that the printer is connected to a wireless network and is ready for use.

The blinking WiFi light on your printer could indicate that it's trying to communicate with your wireless network or it's not connected to your wireless network anymore. A quick fix to this problem can be achieved by rebooting your system. Simply unplug and re-plug your printer and your wireless router into the power outlet and reboot your computer. Once everything turns back on, check the status of the WiFi light and try to print again to verify that the problem is fixed.
You can also do the following steps to reset the printer wireless network adapter:1. From the printer operator panel, press the Setup button.2. Select Network Setup.3. Select Reset Network Adapter.4. Hit the OK button.
The WiFi light will momentarily turn off and then on solid orange. You can then try to reconfigure the printer to connect to wireless network using the Lexmark Wireless Setup Utility application on your computer. Go to Start menu > Programs > Lexmark 4600 Series folder > Lexmark Wireless Setup Utility. Simply follow the instructions on your computer screen.
However, if you wish to have it connected directly to your computer. Simply connect the printer with the USB cable that came with it in the package.
Should you still need assistance, please leave a comment to my response and I'll get back to you. Should this resolves your problem, your rating will be greatly appreciated.

The blinking WiFi light on your printer indicates either your printer is trying to communicate with your wireless network or your printer is not connected at all. For a quick fix, try to disconnect your printer from the power outlet. Power cycle your router and reboot your computer. Then, power on your router first, then your printer and lastly your computer. Check the WiFi light on your printer. If it goes to a solid green, that means you are connected back in your network. If not, you may reset your printer's wireless network adapter to its default settings. From the printer operator panel, press the Setup button > Network Setup > Reset Network Adapter to Default. The WiFi light on your printer will momentarily turn off then back on solid orange. Then try to run the Lexmark Wireless Setup Utility on your computer to reconfigure your printer to connect to your wireless network.
I hope this helps.

The blinking WiFi light on your printer indicates either your printer is trying to communicate with your wireless network or your printer is not connected at all. For a quick fix, try to disconnect your printer from the power outlet. Power cycle your router and reboot your computer. Then, power on your router first, then your printer and lastly your computer. Check the WiFi light on your printer. If it goes to a solid green, that means you are connected back in your network. If not, you may reset your printer's wireless network adapter to its default settings. From the printer operator panel, press the Setup button > Network Setup > Reset Network Adapter to Default. The WiFi light on your printer will momentarily turn off then back on solid orange. Then try to run the Lexmark Wireless Setup Utility on your computer to reconfigure your printer to connect to your wireless network.
I hope this helps.

Since it sounds like an issue with the Power first try to release flea power.Disconnect the charger,remove battery,press and hold down the power button for 30 seconds.Reconnect the battery and charger.Turn on system and check if it turns on. For further help please check Dell Inspiron 1525 Manual. Also confirm if the light on the charger stays on,when connected to the system.

The light indicates that the printer's trying to connect to a wireless network. If the blinking wifi light has been going on for quite some time now but connection is still not going through, you will need to reset the printer's wireless network adapter. To reset the network adapter on Lexmark X6570, press Settings button > Network Setup > Wireless Setup > Reset Network Adapter to Factory Defaults. The wifi light will momentarily turn off then on and should be solid orange then. Try to reconnect the printer for wireless connection.

using your pc/laptop you will have to create a new connection an search for the printer when this has been done, make sure the printers wireless is enabled before attempting to create a new connection

Good day! There are things you need to check to successfully connect the printer for wireless connection.
1. Make sure the wifi light on the printer is solid orange before continuing. If not, go to Setup > Network Setup > Reset Network Adapter to Defaults. Wifi light should turn off, then wait for it to turn solid orange.
2. WEP key can be ASCII or HEX(hexadecimal) depending on what was assigned to it. You may be using an incorrect WEP key. Just to make sure, access your router setup page and double-check the WEP key assigned to it. If you don't know how to access the router setup page, you can always ask assistance from either your internet service company or the router's manufacturer.
Once you get the correct WEP key and wifi light solid orange on the printer, try connecting the printer again for wireless connection. Good luck!