My image runner reports paper jam and i have followed steps on panel to clear it but to no avail

clean all the rollers with a little soap and water then dry them. good luck

Paper jams can be true or false. A false paper jam occurs when the error message displays, but no jammed paper is in the product. The following solutions apply to both true and false paper jam errors.

Print a self-test report Use the following steps to print a self-test report.

1. Load plain white paper in the input tray.
2. Press Setup , and then press 2 . The Print Report menu displays.
3. Press 1 to select and print a Self-Test Report
   

Solution one: Clear the paper jam Step one: Remove loose paper from the tray Remove any loose sheets of paper from the input tray and the output tray.

Step two: Clear the jam from the back of the All-in-One

1. Figure 2: Remove the rear access door
2. Gently pull any jammed paper out of the rollers inside the product.
3. Carefully remove any scraps of paper that are still stuck in the product.
4. Reattach the rear access door. Insert the two posts on the right side of the door into the holes on the product, and then push the door in until it snaps into place.
5. Reconnect the power cord to the back of the product, and then press the Power button ( ) to turn on the product.

Step three: Clear the jam from the front of the All-in-One Follow these steps to remove the paper jam from the front of the product.

1. Without opening the cartridge access door, check the tray for jammed paper that you cannot remove from the back.
2. If you see jammed paper, gently pull it out.
   

Step four: Print a self-test report

• If the issue persists , continue with the next solution.

Solution two: Make sure that the carriage can move freely Follow these steps to make sure that the carriage can move freely. Step one: Check the paper path

1. Check for any paper or object that might be stopping the carriage. Figure 4: Example of paper stuck in cartridge access area
2. Remove any paper or objects you find.
3. Reach inside the product, and then manually move the carriage.
   • If the carriage is stuck on the right side , move the carriage to the left side of the product.
   • If the carriage is stuck on the left side , move the carriage to the right side of the product.
   • If the carriage is stuck in the middle , move the carriage to the right.
4. Remove any paper or obstructions found.
5. Make sure that the carriage can move freely across the width of the product by gently pushing the carriage to the left, and then to the righ

Step two: Print a self-test report

• If the issue persists , continue with the next solution.
• If the self-test report does not print , continue with the next solution.

Solution three: Clean the rollers and the rear access door Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Follow these steps to clean the paper feed rollers inside the product. Step one: Clean the rollers

1. Press the Power button ( ) to turn off the product.
2. Disconnect the power cord from the back of the product.
3. Press in the tab on the left side of the rear access door, and then pull the door away from the product to remove it. Figure 6: Remove the rear access door
4. Lightly dampen a clean, lint-free cloth with bottled or distilled water, and then squeeze any excess liquid from the cloth.
5. Press the cloth against the rollers and rotate them upwards with your fingers. Apply a moderate amount of pressure to remove any dust or dirt buildup. Figure 7: Rotate the paper feed rollers
6. Make sure that the paper feed rollers on the rear access door are clean, free of paper bits, and rotate freely.
7. Clean the surface and the rollers of the rear access door the same way you cleaned the large rollers inside the product.
8. Replace the rear access door. Insert the two posts on the right of the door into the holes on the product, and then push the door in until it snaps into place.

Solution four: Service the product

Give a call to HP Tech support team they will try to resolve your issue. You can contact them (877-690-9305) Support For Hp Printer

I have the same problem.... trying to use lubricants and done some cleaning, but no luck... till i found out that using an extension cord with several devices plugged in will lessen the amount of current that flows to the devices.. that's why the printer's motor can't able to do his job because of no enough power.... Connect the printer's plug directly to the wall...


it works for me....


---ritchie---

Use the following steps to print a self-test report. Load plain, white paper into the input tray.
Press Setup on the product control panel.
Press 2 to select the Print Report menu.
Press 6 , and then press OK to print a self-test report
Solution one: Clear the paper jam
Step one: Remove any loose paper
CAUTION: Never pull jammed paper from the front of the product. If you can pull it from the rear of the product or the tray, always try the rear first. Pulling paper from inside the front cover can cause mechanical damage to the product.

1. Press the Power button ( ) to turn off the product.
2. Disconnect the USB cable from the rear of the product.
3. Disconnect the power cord from the rear of the product

There are too many steps so please follow up from

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00441807&cc=us&lc=en&dlc=en&product=441125&tmp_track_link=ot_search

Solution one: Turn the All-in-One off and on again Follow these steps to turn the product on, and then off again, to reset the print mechanism.

1. Press the Power button ( ) to turn off the product.
2. Wait 15 seconds.
3. Press the Power button ( ) to turn the product on again.
   NOTE: The product might go through a warm-up period of up to two minutes. The product lights might flash and the carriage might move. Wait until the warm-up period is complete before proceeding.
4. Try to print a self-test report. See the steps on how to print a self-test report at the top of this document.

• If these steps resolved the issue , and the self-test report prints , there is no need to continue troubleshooting. Reconnect the USB cable, and then try to print again.
• If the issue persists , continue with the next solution.
• If the self-test report does not print , continue with the next solution.

Solution two: Clear any paper jam Jammed paper can cause the carriage to stall. Follow these steps to clear any jammed paper. Step one: Remove any loose paper Remove any loose paper from the input tray and output tray. CAUTION: Do not remove jammed paper at this stage. Trying to clear a paper jam from the front of the product can damage the print mechanism. Step two: Clear the paper jam from the back of the All-in-One Use the following steps to check for and remove jammed paper from the back of the product.

1. Press the Power button ( ) to turn off the product.
2. Disconnect the USB or Ethernet cable from the back of the product.
3. Disconnect the power cord from the back of the product.
4. Remove the rear door. Push the door latches toward each other, and then pull the door away from the product. Figure 1: Remove the rear door Illustration of removing the rear door
5. Gently pull the paper out of the rollers. CAUTION: If the paper tears when removing it from the rollers, check the rollers for torn pieces of paper that might remain inside the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur.
6. If you are printing labels, see if any are missing from the label sheet. If any labels are missing, find them inside the product, and then remove them carefully.
7. Reattach the rear door. Gently push the door forward until it snaps into place.

Step three: Clear the paper jam from the front of the product Follow these steps to remove the paper jam from the front of the product.

1. Open the cartridge access door. Figure 2: Open the cartridge access door Illustration of opening the cartridge access door
2. If you find paper jammed in the product that cannot be removed through the rear door, gently remove the paper through the front of the product.
   NOTE: Remove paper from the front of the product as carefully as possible. If any torn pieces of paper remain inside the product, more paper jams are likely to occur, and this could damage the print mechanism.
3. Close the cartridge access door. Figure 3: Close the cartridge access door Illustration of closing the cartridge access door
4. Reconnect the power cord to the back of the product.
5. Press the Power button ( ) to turn on the product.
6. Try to print a self-test report. See the steps on how to print a self-test report at the top of this document.

• If these steps resolved the issue , and the self-test report prints , there is no need to continue troubleshooting. Reconnect the USB cable, and then try to print again.
• If the issue persists , continue with the next solution.
• If the self-test report does not print , continue with the next solution.

Keep in this LINK.

The troubleshooting procedures that follow are organized according to location; to find out the location and the nature of a jam, use service mode (COPIER>DISPLAY>JAM).

Dear sir,

i am giving u setp to solved your problem,

Step one: Remove any loose paper.
Step two: Clear the jam from the back of the All-in-One
Step three: Clear the paper jam from the front of the All-in-One Step four: Clear the jam from the automatic document feeder Step five: Print a self-test report Thanks For Your Time,

Print a self-test report Use the following steps to print a self-test report.

1. Load plain white paper in the input tray.
2. Press Setup , and then press 2 . The Print Report menu displays.
3. Press 1 to select and print a Self-Test Report .

IMPORTANT! Try to print a self-test report after every solution even if the solution resolves the issue. Solution one: Clear the paper jam Follow these steps in the order presented to resolve the paper jam. Step one: Remove loose paper from the tray Remove any loose sheets of paper from the input tray and the output tray. CAUTION: Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage the print mechanism

Solution one: Clear the jam from the back of the All-in-One Follow these steps to clear a paper jam from the back of the product. Step one: Remove any loose paper Remove any loose paper from the input tray. CAUTION: Do not remove jammed paper at this stage. Step two: Clear the jam from the back CAUTION: Always clear paper jams through the back door if possible. To avoid tearing the paper and damaging the print mechanism, pull paper from the product slowly and gently. Avoid touching the internal components of the product.

1. Disconnect the power cord from the back of the product.
2. Remove the rear door. Push in the two release tabs, and then pull the door toward you.
3.