Bluetooth headset will not pair up with my LG DARE Phone, My phone trys to add it, but it cannot find the device to connect

Phone: Turn on Bluetooth and Bluetooth visibility. Keep it close to the headset (20 cm).2. Headset: Switch it off. Press and hold down the on/off key until the pairing icon appears on the display.3. Phone: If your phone supports auto pairing, press YES when Add device? appears to complete the procedure. If not, continue with the next step.4. Phone: Follow the applicable User guide to pair with a Bluetooth headset. You may need to enter a headset passcode (0000).

You may need to do a hard reset on your phone to re pair it back with your cell phone, let the battery go empty, remove put back in charge. Make sure that the headset is flashing red/ blue, this tells you that your headset is looking for a bluetooth application.

Plantronics Voyager 520 User's Guide

Good luck from Headsets Direct!

Each pair of BT enabled phone and headset is a particular world. I don't have the Plantronics, but my LG phone pairs fine with my Lubix stereo headsets. I'll tell you how I managed to pair them: I put my headsets in pairing mode. Then, on my phone, I go to 'Connectivity > Bluetooth > Device list > Options > New'. If my bluetooth stack is off I'm prompted to turn it on. It starts to search for devices, and comes up with my BT headsets' name, I press 'Pair', it prompts me for the pairing code. I enter '0000' (the same code for your Plantronics' headsets, by the way) and Ok. Then, back to the Device list, I select the BT headsets and go to 'Options > Connect'. I'm good to go. After listening to music, I use to go again to 'Connectivity > Bluetooth > Device list', select the headsets and press 'Options > Disconnect'.
Hope it works for you.
Cheers! Carlos

First, open the phone's Bluetooth screen. On the HBM-710, press and hold the button on the face for about five seconds, or until the light comes on and STAYS on. Now find the headset with your phone and pair it.

Hope this helps!

I have had the same issue with MY Samsung bluetooth headset.

Here's the sequence that works for me:

1. Delete the headset under the bluetooth menu.
2. Turn off the bluetooth
3. turn on the blue tooth
4. Add the headset back. The default pair code for most devices is "0000" or "1234"
5. Try to enable/connect. If it fais, simply power off the enV.
6. Power on and try to connect again (just connect, not pair)
7. Headset will then pair.

KingGypsy in Phx.

Hi,

follow the steps below:
• Setting the headset into pairing mode
1) Ensure the headset is fully charged
2) The headset must be switch off
3) Press and hold the on button for +- 8 seconds until the light flashes red-blue
4) The headset is now in pairing mode
• Searching for the headset on the phone
1) Go to “settings” or “connections”
2) Select Bluetooth, then options
3) Select Devices and click add
4) The phone should search for any available Bluetooth devices and display what was found
5) Select the Motorola device and click add
6) You will be required to enter in a pass code which is standard ‘0000’
7) If successful then the headset will start flashing BLUE every few seconds.
• The headset is now paired with the phone

Hope this helps
Season's Greetings from Fixya!

Chris (ziraffa)

follow the steps below:
• Setting the headset into pairing mode
1) Ensure the headset is fully charged
2) The headset must be switch off
3) Press and hold the on button for +- 8 seconds until the light flashes red-blue
4) The headset is now in pairing mode
• Searching for the headset on the phone
1) Go to “settings” or “connections”
2) Select Bluetooth, then options
3) Select Devices and click add
4) The phone should search for any available Bluetooth devices and display what was found
5) Select the Motorola device and click add
6) You will be required to enter in a pass code which is standard ‘0000’
7) If successful then the headset will start flashing BLUE every few seconds.
• The headset is now paired with the phone

Hope this helps
Season's Greetings from Fixya!

Chris (ziraffa)

When pairing two phones, you need to set up the connection on both phones. One will ask you to enter the password when you are creating the new connection, which you will then need to enter on the second phone to complete the connection. This ensures that only people you allow to connect (people you gave the code to) can connect to your device.

As for pairing your headset, try this link:

http://www.phonedog.com/cell-phone-research/blog/how-do-i-pair-my-bluetooth-headset-to-my-phone.aspx

try to power cycle the cellphone by turning it off and remove battery, then reinstall and turn it back on


For headset pairing

How to pair the phone with a Bluetooth™ headset The phone identifies and maintains up to 16 devices which are displayed in a list. To add a new device or pair a headset via bluetooth, turn Bluetooth™ on in both devices.

1. Put headset in pairing mode. See Headset User Guide for more information, if needed.
2. Turn on Bluetooth in your phone, Go to menu, [SETTINGS] > [CONNECTIVITY] > [BLUETOOTH] and press "Select"
3. Choose [TURN ON] , press "Select"
4. Choose [MY DEVICES], press "Select"
5. Choose [NEW DEVICE], press "Select"
6. Choose the headset to be paired and press ' Select '
7. Enter the pass key '0000', press "Ok"

Link for headset setting, just choose the headset model

http://www.sonyericsson.com/cws/support/products/pairinginstructions/w300i?cc=us&lc=en

If you are using a different device the just set the Bluetooth to on on it as well

Push and hold both vol(+) and vol (-) at the same time for approx 2 secs. The headset will falsh green and red lights. Get your phone to search for bluetooth devices. It should find the headset. Enter pairing code 1234 in phone. Done