It's been 10 minutes and no responses, how come?

get it serviced (call)
or RTM<
the RTM read the service manual
end.

Dealer or mobile lock smith . unless you have a professional scan tool that can program keys . For about $1,500 you can buy a autel scanner . Immobilizer System Component Programming
10-Minute Immobilizer Relearn
This 10-minute relearn procedure will relearn the prerelease password and the challenge/response data between the theft deterrent module (TDM) and the engine control module (ECM).
Connect a scan tool to the vehicle in the pass-thru arrangement.
Turn ON the ignition, with the engine OFF.
Ensure that all power consuming devices are turned OFF on the vehicle.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions, using the Pass-Thru method. Ensure the correct programming selection is chosen based on component being replaced or programmed. For this procedure, go to the V.T.D. Vehicle Theft Deterrent Learn menu and choose the Vehicle Theft Deterrent Learn, ECM, or PK3 Replaced selection.
At this point the scan tool must remain connected for the duration of the 10-minute relearn procedure.
Important:
• The scan tool will initially display 12 Minutes. The first 2 minutes allow the scan tool to initialize the appropriate control module. The remaining 10 minutes is the relearn timer.
• On some vehicles the security indicator may be illuminated for the duration of the 10-minute relearn procedure.
Observe the scan tool, after approximately 10 minutes the scan tool will display "Programming Successful, Turn OFF Ignition". The vehicle is now ready to relearn the key information and/or the passwords on the next ignition switch transition from OFF to CRANK.
Turn OFF the ignition and wait 2 minutes.
With a master vehicle key, turn the ignition to the RUN position for 15 seconds, then start the vehicle. The TDM and ECM have now relearned the pre-release password and the challenge/response data.
With a scan tool, clear any DTCs.

just remove the battery and connect it again. connect the power cord and leave it for 10 minute and try after 10 minutes switch on the button.

Hope this helps. Please rate my response.
Thanks.
Have a good day

P1000 is not really a fault code, if there are no there are no other codes stored then perform the following:

Disconnect the positive terminal on the battery, hold the terminal to the chassis for 2 - 3 seconds, this defuses the ecu and drains stored data thus clearing P1000.

Now wait 10 minutes.

Then reconnect battery.

Start car *without touching gas pedal*

Leave car idling for a good 5 - 10 minutes then jump in and go on a minimum 12 mile drive, you will need to perform a few normal driving conditions, fast, slow, stop, pull away etc so just a normal day to day trip to the town would suffice.

Hopefully this will sort it, if not report back

Regards

Lloyd

Hi and welcome to FixYa. I am Kelly

I could be of much better help with a complete model number I.e. (example 110.XXXXX)

The wait is supposed to be 10 minutes. go back and turn off your breaker by "Physically" pushing it with conviction to the OFF position and wait 10 minutes.

If after 10 minutes the cooktop is STILL locked:

Push the touch pad that looks like a padlock for at least 5 seconds. The lock light should go out.

If it does not go out I will need your model number to go any further.

Thanks for using FixYa and I will be watching for your response.

Kelly

You are under warranty. Use the Customer Service Phone# and question why this is not fixed.

It sounds like it can be alternator or body grounded antenna problem. You should also check and see if the problem starts with the heater coming on.

The heater would start after the car heats up(10 minutes) or the Alternator would have finished charging and switched into idle mode( about 10 minutes).

The flame should cycle on and off in response to the thermostat. If it is going out and not coming back on several minutes later then the exhaust vent may be clogged. Check the lint filter and exhaust vent all the way to the vent outlet to make sure they are not clogged.

try holding down the middle button and the menu button at the same time for about a minute then it should restart itself

Hello,
Your tv having the main board defective. please call 323-767-6030.
and I will go through with you.