20 Most Recent
Kyocera CS-2550 Black and White Copier - Page 4 Questions & Answers
Kyocera km 3050 has a new toner but says toner empty
If your Kyocera KM 3050 printer is displaying "toner empty" message, even though you have replaced the toner cartridge with a new one, it's possible that the toner sensor inside the printer is malfunctioning or is dirty. You can try the following steps to fix the problem:
1. Open the front cover of the printer and remove the toner cartridge.
2. Look inside the printer, and you should see a small sensor that detects the toner level. This sensor may be dirty or covered with toner particles.
3. Clean the sensor with a soft, dry cloth and reinsert the toner cartridge into the printer.
4. Close the front cover and power on the printer.
If the problem persists, try resetting the printer's toner counter. Here is how to do it:
1. Press the "System Menu" button on your printer.
2. Scroll down to "Service" and press the "Enter" button.
3. Scroll down to "Maintenance" and press the "Enter" button.
4. Scroll down to "Reset Toner Counter" and select it.
5. Restart the printer and check if the problem has been resolved.
If none of these steps work, there might be a more serious hardware issue with your printer's toner sensor, and it's advisable to contact a Kyocera printer support expert or service center for assistance.
Why is my printer Kyocera Ecosystem P3045dn producing vertical mark on printed sheet?
If your Kyocera Ecosystem P3045dn printer is producing vertical marks on printed sheets, there could be a few potential causes for this issue. Here are some troubleshooting steps you can take:
- Check the print cartridge: Inspect the print cartridge for any damage or defects. Ensure that it is installed correctly and securely in the printer. If the cartridge is low on toner or nearing its end of life, replace it with a new one.
- Clean the print head: The print head may have accumulated dirt, debris, or dried ink, which can cause vertical marks on the printed sheets. Refer to the printer's user manual for instructions on how to clean the print head properly. Use a lint-free cloth or recommended cleaning materials provided by the printer manufacturer.
- Check the drum unit: The drum unit could be dirty or damaged, leading to the production of vertical marks. Remove the drum unit according to the printer's instructions and inspect it for any signs of damage or wear. Clean the drum unit using a soft, lint-free cloth. If the drum is damaged, consider replacing it.
- Inspect the paper path: Check the paper path for any obstructions or debris that might be causing the vertical marks. Look for torn or wrinkled paper, as it can leave residues on the print path. Remove any obstructions and ensure the paper is loaded properly in the tray.
- Adjust print settings: Ensure that the print settings in your computer or printer driver are correctly configured for the paper type and print quality. Adjust the print density or quality settings to see if it affects the appearance of the vertical marks. You may need to experiment with different settings to achieve the desired result.
- Update printer firmware and drivers: Outdated printer firmware or drivers can sometimes cause printing issues. Visit the Kyocera website and download the latest firmware and drivers for your printer model. Install the updates according to the provided instructions.
I have kyocera 1800 and its displaying kyocera logo after turning on and it stays just like that.What can be wrong?
If your Kyocera 1800 printer is displaying the Kyocera logo and not proceeding further, it suggests that the printer is stuck in the boot-up process or experiencing a startup issue. Here are a few troubleshooting steps you can try:
- Power cycle the printer: Turn off the printer and unplug it from the power source. Wait for about 30 seconds, then plug it back in and power it on. This can often resolve minor software or hardware glitches.
- Check the connections: Ensure that all cables, including the power cable and any data cables (such as USB or Ethernet), are securely connected to the printer and the corresponding devices (e.g., computer or network router).
- Perform a hard reset: Locate the power button or switch on the printer and hold it down for about 10 seconds to perform a hard reset. This can help clear any temporary settings or errors that may be preventing the printer from booting up properly.
- Update firmware: Visit the Kyocera website and check if there are any firmware updates available for your printer model. If updates are available, follow the instructions provided by Kyocera to download and install the latest firmware. Firmware updates often address known issues and improve the overall functionality of the printer.
Kyocera Taskalfa 266ci : System Error F375.
The "System Error F375" message on a Kyocera Taskalfa 266ci copier/printer is indicating a problem with the finisher.
Here are a few steps you can try to troubleshoot the problem:
- Check the finisher: Make sure that the finisher is properly attached and that there are no loose or damaged connections.
- Check the finisher settings: Make sure that the finisher settings are correct and that the finisher is not in an error state.
- Check the finisher paper tray: Make sure that the finisher paper tray is not full or jammed.
- Check the finisher gears: Make sure that the finisher gears are not jammed or damaged.
- Check the finisher motor: Make sure that the finisher motor is working properly.
- Consult the manual: Consult the manual for specific troubleshoot and service information for your Kyocera Taskalfa 266ci model.
Kyocera FS-2000D is giving me the following error message "close the top cover"
There could be a few reasons why your Kyocera FS-2000D is giving you the "close the top cover" error message even though the cover is closed. Here are a few things you can try:
- Check the top cover switch: There is a switch located near the hinge of the top cover that tells the printer when the cover is closed. If this switch is stuck or malfunctioning, it can cause the error message. Try cleaning the switch or replacing it if necessary.
- Check the toner cartridge: Sometimes, if the toner cartridge is not seated properly, it can cause the printer to think that the top cover is not closed. Try removing and reinserting the toner cartridge to see if that helps.
- Check the firmware: In some cases, a firmware update can fix issues with the top cover sensor. Check the Kyocera website for any available firmware updates and follow the instructions to install them.
If none of these solutions work, it's possible that there is a hardware issue with the printer that will require professional repair.
I have a kyocera ecosys m6635cidn. it wont print. it keeps saying cassette not installed out of nowhere
The "Cassette Not Installed" error message on the Kyocera Ecosys M6635cidn typically indicates a problem with the paper tray or cassette. Here are a few things you can try:
- Make sure the cassette is correctly installed: Check that the cassette is inserted correctly and fully into the printer. There should be a click sound when it locks into place.
- Check the paper settings: Make sure the paper settings in the printer driver match the paper size and type loaded in the cassette. You can check this in the print driver settings on your computer.
- Check for paper jams: If there is a paper jam, the printer may think that the cassette is not installed. Open the printer and check for any paper jams or debris inside.
- Reset the printer: Try turning off the printer and unplugging it from the power outlet. Wait a few minutes and then plug it back in and turn it on. This will reset the printer and may resolve the issue.
If none of these steps work, it may be necessary to contact Kyocera technical support for further assistance.
I have a kyocera ecosys m2540dn printer and i get the screen message "replace toner"!
The error message "replace toner" indicates that the printer's toner cartridge needs to be replaced. However, since you mentioned that you already replaced it with a new one, there may be a few reasons why the error message is still appearing:
- The toner cartridge may be defective. Even though it is new, it may have a defect that is preventing it from being recognized by the printer. Try replacing it with a different toner cartridge.
- The toner cartridge may not be compatible with your printer. If you are using a non-genuine toner cartridge, it may not be compatible with your printer. Try using a genuine Kyocera toner cartridge.
- The toner sensor or other hardware may be malfunctioning. In some cases, the error message may be caused by a malfunctioning toner sensor or other hardware issue. In this case, you may need to contact a Kyocera service technician for further assistance.
I hope this helps!
Kyocera KM-C2525E Yellow cartridge will not load. Message please replace cartridge
Here are some steps I feel you can take to resolve the issue with your Kyocera KM-C2525E yellow cartridge:
Check the cartridge chip - The yellow cartridge has a small chip on it that communicates with the printer. If the chip is damaged or dirty, it can prevent the cartridge from being recognized by the printer. Try cleaning the chip with a soft, dry cloth and reinserting the cartridge.
Check the cartridge contacts on the printer - The printer also has contacts where the cartridge is inserted. If these contacts are dirty or damaged, it can prevent the cartridge from being recognized. Try cleaning the contacts with a soft, dry cloth.
Perform a drum refresh - The drum in the printer can sometimes become coated with toner, which can prevent the cartridge from making proper contact with the printer. Try performing a drum refresh from the printer's control panel to clean the drum.
Reset the printer - Sometimes resetting the printer can clear any issues with the cartridge recognition. Try turning off the printer, unplugging it from the power source, and waiting a few minutes before plugging it back in and turning it on.
Replace the cartridge sensor - If none of the above steps resolve the issue, it could be due to a faulty cartridge sensor. The sensor detects when a cartridge is inserted and communicates with the printer. You may need to replace the sensor to resolve the issue.
How to resume Kyocera KM4050 kx if it shows paused from printing source e.g computer?
If the status from the printing source writes "paused" despite the green tick, there are a few possible reasons why this may be happening:
- Printer software: The printer software may be set to pause the print job. Check the printer software settings to see if there are any options to pause the print job.
- Print queue: The print job may be paused in the print queue. Check the print queue on your computer or device to see if the print job is paused. If it is, try resuming the print job.
- Paper jam: A paper jam can cause the printer to pause the print job. Check the printer for any paper jams and clear them if necessary.
- Low ink or toner: If the printer is low on ink or toner, it may pause the print job. Check the ink or toner levels and replace them if necessary.
- Connectivity issues: Connectivity issues between the printer and the computer or device can also cause the print job to pause. Check the connection between the printer and the computer or device and make sure it is properly established.
If you're unsure about any of these steps or are not comfortable troubleshooting the printer on your own, it's always best to contact the printer manufacturer or a professional technician for assistance. They can help diagnose and fix the problem safely and effectively.
How can resolve error code 08 in Kyocera FS-1020MFP printer?
Error code 08 on a Kyocera FS-1020MFP printer typically indicates a problem with the printer's firmware or hardware. Here are some steps you can try to resolve the error:
- Restart the printer: Turn off the printer and unplug it from the power source. Wait a few minutes, then plug it back in and turn it on.
- Check the connections: Make sure all cables and connections to the printer are secure and properly connected.
- Update the firmware: Check if there is a firmware update available for your Kyocera FS-1020MFP printer. Updating the firmware may resolve the error.
- Reset the printer: Perform a hard reset on the printer by unplugging it from the power source, waiting a few minutes, then plugging it back in and turning it on.
- Contact Kyocera support: If the error persists after trying these steps, contact Kyocera support for further assistance. They may be able to diagnose and resolve the issue.
Note: These steps are general suggestions and may vary depending on the specific m
How to resolve error code 08 in kyocera FS-1020MFP
Error code 08 in a Kyocera FS-1020MFP printer is a communication error and can be resolved by trying the following steps:
- Check the cable connections: Make sure that the cable connections between the printer and computer are secure and properly connected.
- Restart the printer: Turn off the printer and then turn it back on. This can often resolve communication errors.
- Try a different cable: If the error persists, try using a different cable to connect the printer to the computer.
- Update the printer driver: Make sure that you have the latest printer driver installed on your computer. You can download the latest driver from the Kyocera website.
- Reset the printer: Perform a reset on the printer by unplugging it from the power source for a few minutes and then plugging it back in.
- Check the computer's firewall settings: If the error persists, check the firewall settings on your computer to make sure that it is not blocking communication with the printer.
- Contact Kyocera support: If the error continues to persist, contact Kyocera support for further assistance. They will be able to provide more specific guidance for resolving the error.
Not finding what you are looking for?