Top 20 D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 9 Questions & Answers

is not compatible with a mac computer

reset the modem by pressing the reset button for some time and then create new login. it shud work
cheers!

I am actually posting a link to give you steps to this, The SSID or Network name and the wireless key is what you will need. It is usually written on the router itself.
http://www.support.dlink.com/emulators/wbr2310/wireless.htm

The default settings you need to change is Admin and user, Hope this link will help you.
Thanks
Lani

After confirming that your internet service is not down, perform the following steps:

Open your command line prompt box on your computer by typing in cmd in the box that is labeled search or run.

From that black prompt box that comes up, type ipconfig/release and then hit enter.

Then type ipconfig/renew.

If that does not work, unplug the USB leading to the router from your modem, then unplug power from the modem, then unplug power from the router.
Wait at least five minutes before doing anything more.

Reconnect power to the modem and wait for a connected status...this may take a few minutes.

Then plug the USB cable from the wireless router back into the modem. Then reconnect the power back to the router. Wait for connection status.


Once connected, you can configure the router over your computer by typing the IP address 192.168.0.1 and hit enter.
This will bring you to an extensive user menu for your router. Navigate the pages until you locate the selection for a firmware update. This may not pertain to your problem you had but in any case may likely make your router operate better.

If your router is not accepting the username and password that you changed or the default information then your best bet is to press the reset button on the back of the router for 5-10 seconds. This will clear all the settings back to the manufacture default settings but will allow you to sign back into it and complete the setup again.

hxxp://www.retrevo.com/support/D-link-DI-524-Wireless-Routers-manual/id/420ci365/t/2/
Check to see if this is the correct model. If so, change the "x"s to "h" in the link. Not sure if I can post live links here.

By going to the security setting in the router and assigning a WAP/WEP "Key" this will then enable security. Please consult your manual for how to do this.

ftp://ftp10.dlink.com/pdfs/products/WBR-1310/WBR-1310_ds.pdf
manual above

Go to D-Link - TechSupport FAQ

you need to set a password and this has to be done using the router web interface (192.168.1.X) find the default gateway of you computer - run ipconfig on command prompt will let you know the defaukt gatway - once you are loged in to that web interface - go to wireless section and enable the security as need - this will make your network as private.

router Web interface can be opened by typing just the default gateway on address bar of IE .

What problem? Just in case go to D-Link - TechSupport FAQ.

If any more problem encounter,post or thumbs back.

Go to D-Link - TechSupport FAQ and select model/version and start a new configuration.

You can follow these steps in enabling wireless security on your router and do this steps using a computer wired to the router since once you save the settings your wireless network will be secure.<br /><br />1) Open the internet browser and type the address 192.168.0.1 to login to the router. The default username is "admin" and leave the password box empty.<br />2) Click "Wireless Settings" on the left side.<br />3) Select the Security Mode ,Enable WEP Security.<br />4) Select the Authentication ,Shared Key.<br />5) Select the WEP Encryption , either 64-bit or 128-bit.<br />6) Select the Key Type ,HEX (only A-F and 0-9 number allowed) or ASCII (all number and character allowed).<br />7) Enter a WEP key as your security password to login to your wireless later.<br />8) Press Save Settings to save all settings changed. Reboot the router.<br /><br />

.Log into router ( 192.168.0.1) enter into the browser window.
2. Verify wireless router name( on the computer) >>> ( on/off) on the status page in the router.
3.Note router name you are connecting to.
4.. Check the laptop do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address.
6.Note router name you are connecting to.
7. Here is the instruction set for your model router :to set it up wireless follow the emulator instruction at this link:
http://support.dlink.com/emulators/wbr1310_revA/104/wizard.htm

This is for all routers to set up wirelessly.

I suspect that you have port forwarding rule (virtual server) on port 443 (https) on your router. Try to remove rule or just reset router to factory settings. I have the same router and this problem did not happen. You can also install Router Commander program to boost up router performance.

Hello emanuelav716, Your router does not need to be connected to a phone line. However is does need to be connected to a cable or DSL modem if you want internet access. If you are just looking for a network inside your home or business the router can be setup that way. Please reply with any other questions or rate this solution if you found it helpful. Thanks! Edward

Are you trying to set up router ?
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.

Click Here for more information about the routers and network

Hi,

Setting up security on a WiFi router is quite simple and straightforward.

All you need to do is login to the router and set up a Network Name (SSID) which will be used to identify the network and then add a passoword to secure the Network.

Once done, any device that connects to the WiFi Network will need to authenticate with the password that has been specified on the Router. This will prevent unauthorized access to your home wireless network.

go to D-Link - TechSupport FAQ

Yes it will be better if you reset the router and reconfigure it back, To reset it just use a pen or paper click to press and hold teh reset button for 10 seconds then power off the router for 10 seconds and power back on and after that if you have the setup CD of the router just run it to reconfigure it back.

To configure the unit on the label there is an IP address and a login name and password that will permit you to open the door.
If the password has been changed there is a reset button somewhere on the backside resessed in accessable with a ballpoint pen.
The CD just makes this process supposedly easier.

There may be firmware updates fir the unit
http://driverscollection.com/?H=WBR-1310&By=D-Link