Top 20
D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 8 Questions & Answers
How to get into the router
To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).
Enter the user name (admin) and your password. Leave
the password blank by default.
If you get a Page Cannot be Displayed error, please
refer to the Troubleshooting section for assistance.
The manual:
http://www.scribd.com/doc/4040609/wbr1310-manual-110
Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!
Thanks, Joe
I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309
Is there a way to
Yes you can - If you do not know the login and password -
You
can reset the D-Link back to the factory defaults by - power off the D-Link,
press and hold the RESET button on the back of the router, then power up the
router. Hold the RESET button for 5 secs and release the RESET button or until
the LEDs flash together.
Connect a LAN cable from the D-Link to the LAN port
on your computer and open a browser. Enter the D-Link's configuration URL
http://192.168.0.1
The default login = admin
The default PW = blank (just
press Enter)
You can now configure the wireless settings, eg. SSID and encryption etc.
To secure your wireless network from unauthorized access,
please cick on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security.
How to install
1st you need to configure the the D-Links wireless settings eg, the SSID and encryption, and the configure the wireless card in the computer/laptop with the D-Link's wireless settings so it can connect to the D-Link.
To secure you wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security
How can I get my WEP id again...I lost it?????
Hi,
This Utility program from HP will help you locate few details on your network
1. SSID ( network name )
2. WEP/WPA Key ( Your network security key )
3. The PC/Laptop IP Address
4. Router IP address
5. Which all Devices are connected to your Router/Network Wireless
6. Which all Network are available nearby your place
7. Let you access the Router Configuration
Click here to Download the HP Network Diagnostic Utility
Download the file on Desktop and Run the program ( Ex. File name = HPNDU.EXE )
Follow the Instructions on the Screen and do accordingly.
Regards,
Ron
My D-link wireless router is
Is there any computer connected to the router ?
If not then you will need to connect the computer to the router.
Do not change any wireless settings on the router with the wireless computer.
you will need to connect the computer to the router with the Ethernet cable.
check the IP address of the computer.
open the router set up page of the router.
Here you can change the wireless settings of the router.
Now once you change the network anme and security on the router, you will need to connect to the wireless network on your wireless computers.
Click Here for step by step instructions
I need a url address
The default address is 192.168.0.1
In your web browser's address bar just type http://192.168.0.1
All computers are slow
delete you temporary internet files Tools>Internet Options> under browsing history click delete, check the temporary internet files box and click delete.
I have just installed my
Yes it is.
Its an indication that the router is working fine and that it is broadcasting wireless signal.
Don't forget to rate this answer if it helps
Wbr1310. i switched laptops to
Step 1 With the unit on, place a paper clip into the hole on the back on the unit labeled
Reset.
Step 2 Hold paper clip down for 10 seconds and release.
Note: Do not repower unit during this procedure.
Step 3 The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.
Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.
Note: The factory defaults username is admin, and there is no password.
If you need more help come back.Post / thumbs / testimonial are welcome!
Lost install disk, need to download install disc.
You can set up your router manually, without the CD.
Make sure that your computer is able to go online directly through the modem.
If your computer is able to go online through the modem, that means the modem is working fine.
You will need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for more information about the routers and network
Unable to go wireless...message says cable is not
Yes, and of course the whole point of wireless is that there is no cable connected!
Did you get a disc with your router? If so, run the disk with your adapter connected.
Ah... you do have an adapter connected, don't you? If not, you will need to buy a wireless adapter to plug into a USB slot on your PC. A wireless router works by receiving a signal from a wireless transmitter in the PC, or from an adapter attached to the PC's USB slot. If you don't have an adapter, you can get one for about £20 to £30. It's definitely worth the money, I assure you!
If you do have an adapter but the router can't 'see' it, you need to check a few things. Check the adapter is properly connected. Check its properties by clicking on its icon in the taskbar - make sure the signal strength is sufficiently high, and that the adapter is attempting to connect to your own router, and not the equipment of someone across the road.
If the router came with an instruction booklet, it should explain how to connect using the wireless facility, and these instructions are usually helpful and well-written. Most importantly, the booklet should tell you where to find the crucial information to type in the first time the adapter tries to 'find' the router. In fact, many routers have a sticker with the wireless connection code stuck to the router itself somewhere, so if you can't find the booklet, look for a sticker on the router itself.
I hope that helps a bit. Good luck!
Can't remember my password for wireless network
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.
Not finding what you are looking for?