20 Most Recent Soyo DYLT032D 32 in. LCD Television - Page 7 Questions & Answers

Call your manufacturer if you are still under man. war. they can replace/repair the unit for you if not they can give you some referrals. Sounds like your powerboard is going to go out on the unit.

I have a philips universal remote changed batteries now the codes lost

Sounds like the Main Mother Board is the problem. Basically, it's the brain inside the TV. Controls and functions is that board's job.
Soyo parts are hard to come by. You can try running the number off the mother board on the internet and maybe a supplier will pop up.
Their Soyo.com web site isn't working. So, I'm thing they maybe out of business.
If you have some electronic experance and if your lucky, the heatsink on the chip processor is the problem.

The problem is the capacitors on the power supply board. There are two of them, the rating is 220uf - 250v - 105C (M). The back side of the capacitor says V9A PET. You need to remove the board, make sure the capacitor is drained, (you can do this by placing a screwdriver across the posts) Use a soldering iron and remove the capacitors. The only place that has replacement parts is at www.mouser.com, Install them, make sure the polarity is correct, re-solder them back into place. Re-connect the board and it should power back up correctly. Good Luck. Steve

The problem is the capacitors on the power supply board. There are two of them, the rating is 220uf - 250v - 105C (M). The back side of the capacitor says V9A PET. You need to remove the board, make sure the capacitor is drained, (you can do this by placing a screwdriver across the posts) Use a soldering iron and remove the capacitors. The only place that has replacement parts is at www.mouser.com, Install them, make sure the polarity is correct, re-solder them back into place. Re-connect the board and it should power back up correctly. Good Luck. Steve

first you have to know witch remote you have there is a 3 button witch has vcr tv and cbl at the top that one there press tv and select at the same time untill the light flashes 3 times release then enter 9-9-1 the pres the tv button untill the tv turns off if you have the newest 5 button remote you will press tv release press and hold setup untill light flash's 3 times then enter 9-9-1 light will flash once entered then press ch+ sevral times untill your tv turns off once tv turns off stop and press setup and that will lock the code inplace i hope that helps

My charter cable company gave me the following three codes for their universal multi unit remote: 10047, 00600, 00629, 00699. The first one was developed by having the remote search for the code and it worked with my unit (identical to yours). The other two were provided by the cable company. Hope this helps!

Hi
Theirs no doubt you have a software problem with this set,happens a lot on the sharp range too,the software will need upgrading to the latest one for that model.Go to manufacturers website they may have it their with a "how to"note

Could the batteries in the remote be dying. Did you try changing them?

Hi Friends, Teddux, and Guest, have a correct answer,
The Caps is a 2200uf x 6.3volts, reemplace all caps with this spec.

thz.

the screws are already removed the should be plugs little ccircles on the back to remove for a wall mount if not check the tv manual

Hello you remove the last four screws on the back of the tv located down at the bottom theres two on each side the stand will slide out...

Check the PSU/ power supply unit not the cord. The cord is never the issue in this complex problem. You may have a blown fuse in the PSU if its a IC intergrated circuit then it needs to be looked at by a qualified Tech.. We only can help you without looking at it, hope this helps Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

I can repair the power supply for you if you like depending on where you live repair is about 150.00 shipping may be a little extra

David
[email protected]

change your source input to the correct video source you are using

like to make contact with you on this I have the same problem I think we should form a class action law suit on this if we can get enough people to join us
[email protected] I'm not sure how to do this If you have any suggestion's It would be helpful feel free to contact me on this please keep me informed thank you Bill Hoffman