20 Most Recent
Sony KP-46WT500 46" Rear Projection HDTV-Ready Television - Page 3 Questions & Answers
Lightning hit sony kv29xbr85
If it was me...I would first check the series of fuses on you main circuit board. Look for any burned components.
The picture looks like a 3D with the egges curving
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
SOLUTION
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Where is the convergence IC
On the large heatsink.
Please do us a favor and rate this solution after reading.
Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com
Common Problem #1) Convergence has gone out
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Common Problem #2) CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
SOLUTION
You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Please do us a favor and rate this solution after reading
Red green color is terrible. 2 D like picture
Your convergence circuit has failed in your tv. Very Common. Repair shop will charge around $300 to fix. Requires replacing STK chips, some resistors, maybe a fuse or two and convergence re-alignment from service menu.
I have a sony rear projection tv kp-46wt500 it has
David, you need to take off the front cover (where the speakers and power button are). On the back there are two screws on each side. unscrew those then pull. There are push in clips holding it on. 4, two on top two on bottom. Just pull hard, you won't break the cover, then find a place to set it aside (you may need to disconnect the front AV hook-up, thats simple, just unplug it like a outlet) and then there will be another panel, held in by four more screws take those out. Then you will find a like 3 inch square thing with 6 plastic screw knobs on it. It goes blue green red (could be different for yours, but should be the same, if not, one of the colors is labeled) Ok, no find the red one and turn it probably counter-clockwise. That will reduce the amount of voltage that the color red gets.
Oh, forgot to say, there are two rows of screw knobs, one says "focus" you can leave that one alone. the other says "screen" that is the one you want to change.
And also, when you are turning it. I'm tlaking like 1/8inch or less turn at a time. If not you can fry it and actually burn out the bulb. But I don't think it is burnt out. Just getting too much voltage
What does the ic 406 and. The ps401 and 402 look
Ic 406 is the audio amp ic. It is on the signal board, that's the one with the tuner on it. It's mounted on an aluminum heat sink with fins on it. It's all by itself. 401 & 402 are small pico fuses normally black in color and you can't tell by looking at them if they are bad. You have to use a continuity checker or an ohm meter.
The signal board board does not have the transformer with the red leads coming out of it.
When set is turned on it comes on breifly and goes
You need to check the bulb in the back of the set as it could be on the way out . just check to see if the bar in the bulb has gone black as it is a good sign the bulb is on it's way out . the bulbs only last 2-3 years or 4000 hours . If thats ok you most probably have dry joints on the tuner , they just need resoldering
Curved horizontal green lines bout
Your TV most likely has one of two possible problems.
Problem #1: Convergence Chip Failure ( common problem )
Here are some of the most common symptoms and example photos of a convergence problem
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
Here is a quick test....
Using your original remote go-to the tv settings then goto the convergence section.
Try to adjust the red and then the blue convergence.
You should be able to move them up, down, left, and right.
If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.
Solution #1
You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.
Problem #2 CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
Picture of a set that needs the fluid changed.
TV set after fluid change
Solution #2
What you will need to do is replace the coolant and clean the crt. You can get a repair kit from www.TvRepairKits.com that includes replacement coolant, photos. instructions, etc
Color problems the coloring is more yellow and I
This model had a major issue with the CRTs failing. The blue CRT is probably bad. The sad news is that Sony is not supporting much of the older CRT style tv's whether it is a projection or direct view type. What Sony has you do is to remove the CRT and box it up then send it to them so they can rebuild it. The problem is the cost in doing this. Plus, to be sure you would not have a problem with the other two CRTs you would also need to send them in too. In either case the cost of doing this would run more than replacing the set with a new LCD panel.
I hope this helps,
Skyassoc
It's hard to describe...And I'm
Ur tv have a problems known as a convergence problems,it dead.The tv have colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.These parts,must be replaced on the tv convergence board to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.
Image is showing in all three colors
Tv have a problems known as a convergence problems,it dead.The tv have colors lines R,G,B mis alignment,have colors shadows pictures or 3D pictures look alike.The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors.These parts must be change on the tv convergence board to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.
Picture is distorted - colors
If convergence (see photos) it can be a do it yourself repair.
Repair involves getting at the two STK-392-560 chips this set should use and replacing them.
My guess here is the chips failed and took out one of the fuses that protect them.
Let me know if you have any questions, I am here to help.
Look at the photos and if they told you something you did not know, rate this solution as very helpful as I do this here for free.
SD TECH
Chips (2 in your set look like this but will have STK-392-560 NUMBER ON FRONT.)
a PAIR OF THEM ON EBAY (I use a seller there) under 14 dollars.
Not finding what you are looking for?