my printer brother dcp-165c wont print black.i already bought a new black ink and replaced the old one but still it wont print.the printer can detect that the ink is full but still wont print black... same as his problem. but my printer brand is brother DCP 560-CN. it also dont print black eventhough the black cartridge is full.
did you take the tape off the new cartridge and is the print head burned out for the black? if you installed the diagnostic's on it then run it and see what it says, otherwise expect the print head to be cooked, however it is possible to get a bad ink cartridge try tapping it on your finger and see if ink comes out if it does not then the ink cartridge is dried out or no good, about %15 of print cartridges are bad on just about any brand printer some more than others.
Posted on May 31, 2009
Error: init unable 50
Printer model: Brother dcp-165c
Pls help me how to solve.
init unable 50 how to resolve this problem..?
Posted on Jun 28, 2011
init unable 48 or machine error 48 in my brother dcp 165-c. pls. tell me how to reset to fix it. thanks
There are several issues that pertain to this code, including a service update. If your printer is still under warranty – visit your local ASC, find one here, this issue is covered! First off, the Service Update, the encoder strip needs to be cleaned with a lint free cloth. The encoder strip is responsible for relaying the position of the print head to the main pcb. If the encoder strip gets dirty, many different problems can occur. The encoder strip is exposed, which allows grease, paper dust, finger prints, ink, etc. to get onto the encoder strip. (The white strip when you open the scanner cover)
If the machine still errors, the encoder strip needs to be replaced – Part Number LS4467001
If the machine still errors, replace the carriage PCB assembly – Part Number LS6543001
If the machine still errors, replace the Printhead – Part Number LK3211001
If the machine still errors, replace the Main PCB assembly – Part Number LT0284011
THANK YOU FOR USING FIXYA! – DON’T FORGET TO RATE OUR SERVICE!
Posted on Feb 03, 2010
My printer is Brother DCP 165C. My problem is that my printer cannot print in black ink although the printer detected the black ink. It has no problem with the colored inks. Aside from this, the device reported that the ink level is always full (black and colored). This problem started since I upgraded to Windows 7. Previously with XP, I have no problem at all. I already downloaded and install the recent driver software from Brother website but still the problem exists. Any solution/suggestion to solve this is very much appreciated. Thank you.
Your black printhead is blocked.
The printhead is deep inside the printer and has to be taken out by the expert and cleaned with the help of 'steam' and hot water. This is because not using the printer for a long time. or using low grade refill inks.
Please select new cartridge only if you are inserting a new cartridge or fully refilled cartridge. Otherwise use old cartridge option. Brother printer has a mechanical sensor and not the electronic chip in the ink cartridges.
After inserting the old used cartridge if you choose 'new cart' option it will show the "Full" ink. You can still print from the exhausted ink cart after covering the sensor in the middle by a piece of paper in emergency.
Posted on Mar 05, 2010
HOW CAN I RESET MY BROTHER DCP 195C?
print unable 4f
Posted on Mar 11, 2010
clean unable 46, See Trouble shooting and routine maintenance chapter in User's Guide.
Hi there. . . okay . . . Follow this step
1.) Unplug your printer.
2.) Plug your printer again while holding the menu button 15 sec.
3.) select 8 by using the arrow buttons ,push OK and select 0 and push OK
4.) then numbers appear looks like this ###:### ###:###.
5.) now push the MONO button until the purge:#### appears on the LCD
6.) Select 2, push ok, select 7,push ok,select 8,push ok, select 3,push ok
7.) - switch off the printer ,switch it on
- ready to print
- CHEERS!
email me if I help you. . [email protected]
Posted on Mar 26, 2010
how to reset brother DCP 165C unable to print
how can i reset my printer for brother dcp 165 printer..?
the erroe will appear in the computer is clean unable 5a...
Posted on May 27, 2011
brother dcp-195c print Unable 70 troubleshooting and routine maintenance chapter
troubleshoot and routine maintenance
Posted on Nov 30, 2010
how to do the clean unable 50 in brother DCP-165C
Hi Good day!! try this method
- Machine off
-
Switch on the machine while holding down the "menu"button until all the
leds are flashing on/off. Now you are in "maintenance" mode.
- press 80
- press the "mono start" button several times until you see "purge: xxxx"
- press "2783" in order to reset the purge counter. You will see: "purge:0000"
- press "99" to exit the maintenance mode
Now
you are able to print again, but actually your ink absorber box is now
full with ink. Ink flooding can happen if you don't replace this ink
box!
Don't forget to vote thanks!!!!
Posted on Nov 04, 2010
brother dcp-165c print unable 50
how ca n i fix my brother dcp 195 c unable 50?
Posted on Jun 07, 2011
597 questions posted
Usually answered in minutes!
422 Questions
374 Questions
242 Questions
245 Questions
120 Questions