20 Most Recent Delta Model 473: Saxony Kitchen Pull-Down/Out Faucet - Venetian® Bronze - Page 4 Questions & Answers

TAKE IT APART. LOOK FOR SMALL SET (ALLEN) NUT/BOLT OR REGULAR NUT/BOLT YOU CAN TAKE OFF THEN TAKE OFF HANDLE AND REPLACE THE O RING.

LOOK UP ON LINE UNDER 3S10H/C VALUE KIT FOR BATH TUB FAUCET. SEE IF THERE IS A MANUAL OR A TROUBLE SHOOTING PAGE.

Hi, there is two possible problems, first off could be the tap jumper or there is air trapped in the pipes. Try replacing the tap jumper, alternatively open all the taps to release the air

DID U TRY LOWS OR HOME DEPOE. OR TRY Rubber Delta Faucet‎

If the copper pipe is indeed leaking, you'll probably need to open the wall to fix it. Sometimes you can open the wall in back of the tile, in the adjoining room. Make sure this is the issue before you start this process.

If it has a filter on the tip remove it and retry.

Delta has a toll free number to call but have your model number ready when you call

Best to follow the steps on this Delta faucet website. Troubleshoot your Faucet

Are you on a well? If so, the most used faucet may smell if your well needs to be disinfected. A cup of bleach will do it...

If you can remove the cartridges, might be able to tell you if the parts for the cartridges are still available, take a picture of that and post it.

First turn off water to faucet. There will either be a set screw or a screw under the cap depending on the style. Once handle is removed there is the bonnet, crescent wrench or channel locks will do the trick. With bonnet off you should be able to remove the white cap and steel ball revealing the spring and boot. That's what you replace. Reverse the order to put back together. And there you have it.

Make sure your battery pack is not touching anything else except for some wood it's sitting on, and that it's at least 2" away from the walls. Also possible is that the wiring from the solenoid to the battery pack is contacting something it shouldn't.

Everything wears out with time. Try going straight to the manufacturer.

Bad link

messy ,, but while u had it apart did u turn on the water to see if water would come out at all... we flushed our line and that cleared up the problem.

I've the tub spout leaking problem. How do I fix it? Tks!

you will need to see if there is a seperate turn off near the shower. (usually behind the wall in an adjoing room. if not you will need to locate the main for your water and turn off the entire house while you fix this problem.. The Home Depot has several how to's on there web site for this issue.

Remove the rubber O ring (turn off Water supply at meter first), then take your O ring to the hardware store to obtain a new one. You may have to stretch the new ring under hot wster before installation, If you do not feel comfortsble doing this yourself, call an expert.

If you have the two handled Delta, the cartridge itself can be replaced with a new one. The old one may have the O-ring seal deteriorating to allow it to move as you see it move. The O-ring itself can also be replaced by itself.If you have the single handle version and the seal the ball sits on is moving, the selas can be replaced, and they are simply fished out with a paperclip bent into a small L to hook the spring and seal and draw them out. If the single handle typ handle is loose it held in place by an "Allen wrench"/hex key wrench. If the handle is loose on a double handle type, just lift the "H" or "C" cap out of the handle and tighten with a phillips screwdriver. It might just be they never installed the screw.

Cna you remove water line feeding hot side to make sure it has correct flow. It could have something blocking inside of water line. And check hot inlet side on faucet to make sure it is open and not blocked.


Remove line you can run water in a bucket to ensure that hot side water line has no blockage in it and have someone help you with turning water off and on for you.