Motorcycles Logo

Related Topics:

Max Speed
Max Speed Posted on Nov 16, 2013
Answered

Programming keyless remote - Harley Davidson Motorcycles

Answer This Question

1 Answer

mike_wade728

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 4 Answers
  • Posted on Dec 10, 2013
mike_wade728
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Problem Solver:

An expert who has answered 5 questions.

Joined: Apr 24, 2010
Answers
4
Questions
2
Helped
526
Points
4

Below is a couple proceedures on the subject --first one sets your personal security code in case you lose your Fob or if the battery should die the second one is ASSIGNMENT of a Key Fob to the bike

Below

programming keyless remote - mail_dir.ashx?url=http%3a%2f%2fwww.fixya.com%2flxp.gif%3ftype%3dimpression%26mailid%3d204&met=0&mt=204 This must be done when you buy a new button type key fob for the Alarm if you lose one.

I assume you know your personal entry code using the directional switches and the key switch to activate , if not , it's in the Owners Manual

If you never set the code,the dealer can help you out here.

1. Set run switch to off
2. ign to acc
3. hold both turn sigs till lights flash
4. use Left Turn Signal to enter number by pushing 7 times
5. use right turn signal as enter key
6. repeat until all 5 are entered and you hit enter

lights should flash and you should be OK.


KEY FOB ASSIGNMENT


The Key fob on TSSM motorcycles must be set so it will operate the alarm system on the vehicle.
This assignment must be completed with no pauses between steps greater than 10 seconds.
Turn the ignition OFF after all key fobs have been assigned.
The programming mode will also exit after 60 seconds has elapsed without detecting any fob signup messages
or turn signal switch activity.
Two key fobs may be assigned to the TSSM.
The first successful attempt to program a fob will disable all previously assigned fobs.
If a second fob is to be programmed, it must be done in the same programming sequence as the initial fob.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How Do I Know If My Car Equipped With A Keyless Entry Remote System? I have a 1999 Ford Windstar. I bought several remotes but can't get my locks to engage. Any help would be appreciated.
Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..
Read full answer
Sep 18, 2021 • Ford Cars & Trucks
tip

Chamberlain Remote Controls and Keyless Entry Systems Programming Instruction...
940D Programming instructions for keyless entry system model Chamberlain 940D.

940CB Programming instructions for keyless entry system model Chamberlain 940CB.

942FP Programming instructions for Fingerprint Keyless Entry System model Chamberlain 942FP.

953D Programming instructions for remote control model Chamberlain 953D.

956D Programming instructions for remote control model Chamberlain 956D.

953CB Programming instructions for remote control model Chamberlain 953CB.

956CB Programming instructions for remote control model Chamberlain 956CB.

750CB Programming instructions for remote control model Chamberlain 750CB.

 KLIK1U Programming instructions for Clicker® Universal Remote Control model Chamberlain KLIK1U.

KLIK2U Programming instructions for Clicker® Universal Keyless Entry System model Chamberlain KLIK2U.


Read full tip
on Jun 09, 2011 • Chamberlain Clicker Universal Remote...
0helpful
1answer

Program new keyless entry remote for 1994 lincoln town car
Great news, you can program a 1994 Lincoln Town Car keyless entry remote yourself! Here are the steps:

NOTICE: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
1. Turn ignition to RUN or ACC.
(Run is forward, just shy of starting car.)
2. Momentarily jump pins in programming connector located behind the glove box.
(The connector will have two pins inside of it, and it will not be plugged into anything. Jumping the pins means to make a connection between the metal inside the plug. You can do this by using any metal, a metal paperclip bent in the shape of a "U" usually works perfect.)
All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote. Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
You can find more keyless entry remote programming instructions here https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm
Read full answer
Jul 16, 2012 • 1994 Lincoln Town Car
0helpful
1answer

2001 mustang keyless entry not working properly what do I do
You did it like this ?
Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
  1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
  1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
  1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
Read full answer
Jan 15, 2018 • 2001 Ford Mustang
0helpful
1answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.
Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!
Read full answer
Nov 28, 2010 • 1996 Ford Econoline
6helpful
1answer

Keyless remotes not working
Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.
Read full answer
Jun 06, 2010 • 1998 Ford F150 Regular Cab
2helpful
1answer

How do i reprogram electronic door locks
Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.
Read full answer
Jun 05, 2010 • 1997 Ford Windstar
0helpful
1answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.
1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.
Read full answer
Jan 23, 2010 • 1996 Chevrolet Corvette
1helpful
1answer

New batteries but remote won't click the door(s) or trunk. Ron
try programming the remote again, here is how u do that. if this doesn't fix the problem the remote may be defective, if you need a new one try ebay, they are very cheap to buy there.

.

Note: Existing keyless remotes will be erased with this procedure.
Existing working remotes will have to reprogrammed also.
1. Locate the programming connector wire located in the RH trunk area.
You may have to pull back right side trunk trim on trunk wall to locate
the single black/white wire.

2. The programming connector wire should have one termial in the plastic
connector on end of black/white wire. Ground the terminal in the connector
to a nearby bolt or trunk latch.
Leave connector wire connected to ground through out procedure.
3. System will now lock and unlock doors automatically to indicate
programming mode has been activated.
4. Press any button on keyless remote. System will respond by locking
and unlocking doors one time to indicate successful programming.
5. Repeat step 4 for to program any additonal keyless remotes including
and existing keyless remotes. Do not remove ground wire between
programming of keyless remotes.
6. Disconnect programming connector wire from ground to exit programming
mode.
7. Test keyless remote(s).
Read full answer
Nov 30, 2009 • 1994 Pontiac Grand Prix
0helpful
1answer

Keyless remote
If u have the system here is how you program it this is from the owners guide.
1.. Turn ignition to RUN or ACC.
2. Momentarily jump pins in programming connector located in LR quarter panel area (Connector will not be plugged
into anything, it will have two pins inside it, if you have to unlug it you have the WRONG one. Not all vehicles
are set up from factory for keyless remotes) All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode
Read full answer
May 10, 2009 • 1993 Ford Explorer Limited
Not finding what you are looking for?

View Most Popular

Motorcycles

Related Question

How Do I Know If My Car Equipped With A Keyless Entry Remote System? I have a 1999 Ford Windstar. I bought several remotes but can't get my locks to engage. Any help would be appreciated.

  • Ford Cars & Trucks

299 views

Ask a Question

Usually answered in minutes!

Popular Questions

2003 sportster wont start or run right when it is warmed up

2000 Harley Davidson XL 1200 C...

How do i adjust a S&S super B carb, cold start

1993 Harley Davidson FXR Super Glide

BIKE WON'T STAY RUNNING AFTER JUMPER CABLES ARE TAKEN OFF....

Harley Davidson Motorcycles

My neutral light does not always come on, how do i

2004 Harley Davidson XL 883...

What is the recommended tire pressure for a dyna

2006 Harley Davidson FXDLI Dyna Low...

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
1979 HD XLH Wiring Diagram Color...

1979 Harley Davidson...

Loading...