How install rear window - 2002 Chevrolet Silverado 1500

Installing a cable to connect the rear window heater in a Ford Street Ka hardtop can be a complex task that requires some mechanical and electrical knowledge. There is no standard cable available in the car, therefore it's necessary to install a new cable to connect the rear window heater.
Here's a general guideline on how to install a new cable for the rear window heater on a Ford Street Ka hardtop:

1. Locate the main power source for the rear window heater. This is typically located under the dashboard or in the engine compartment.
2. Run the new cable from the main power source to the rear window heater. Make sure to route the cable along the existing wire harnesses and avoid any potential hazards such as moving parts or hot surfaces.
3. Connect the cable to the rear window heater. This typically involves removing the cover from the heater and attaching the cable to the appropriate terminals.
4. Test the rear window heater to make sure it is working properly.

It's important to have a good understanding of the car's electrical system, and to be familiar with the tools and materials needed to do the job properly. It's also important to make sure the car's warranty is not void by doing this modification.
A professional mechanic or an auto electrician could be the best choice to do this task. They will have the necessary knowledge and experience to safely and effectively install the cable for the rear window heater on your Ford Street Ka hardtop.
It's important to follow the manufacturer's instructions and guidelines when performing any modification or repairs on your vehicle, to ensure the safety and proper functioning of the car.

94-97 Honda Accord Rear Side Window Install - YouTube

? 6:00
https://www.youtube.com/watch?v=Cgn0EmuY9NU
Jan 8, 2013 - Uploaded by Function Factory
94-97 Honda Accord Rear Side Window Install ... How to fixreplace install a broken power window regulator ..

it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.

1. Start with the ignition in the OFF position.

1. Turn the ignition to the ON position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the OFF position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.

1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.

1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.

------------------------------------------------------------------------------------

• The power rear window is inoperative (Explorer Sport Trac only)

• Circuitry.
• Battery Junction Box (BJB) fuse 3 (30A).
• Central Junction Box (CJB) fuse 20 (7.5A).
• Power rear window control switch.
• Rear window glass motor.

• Go To Pinpoint Test K .

------------------------------

• The power rear window is inoperative (Explorer Sport Trac only)

• Circuitry.
• Battery Junction Box (BJB) fuse 3 (30A).
• Central Junction Box (CJB) fuse 20 (7.5A).
• Power rear window control switch.
• Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.

1. Start with the ignition in the OFF position.

1. Turn the ignition to the ON position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the OFF position.

1. Press the power rear window control switch vent button six times.

1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.

1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.

1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.

1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions

---------------------------------------------------------------------------------------------

Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator

1. Position window approximately half way down in the door.
2. Remove the interior trim panel.
3. Remove the water deflector.
4. Tape the window to door frame to prevent it from moving.
5. Remove the three front door window regulator motor screws.
6. Disconnect the electrical connector from the window regulator motor.
7. Remove front side door window regulator motor.
8. To install, reverse removal procedure.

Window Switch
Front

1. Remove the front door pull cup screws and pull cup from the front door trim panel.
2. Disconnect the electrical connectors from the front door power window control switch.
3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
4. To install, reverse removal procedure.

Rear

1. Remove the rear door pull cup from the rear door trim panel.
2. Disconnect the electrical connectors from the power window control switch.
3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
4. Remove the power window control switch from the rear door pull cup.
5. To install, reverse removal procedure.

http://www.youtube.com/results?search_type=&search_query=rear+window+installation&aq=0&oq=rear+window+install

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .

Removal and Installation

1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .

1. Remove the watershield.

1. Remove the interior weatherstrip.

1. Remove the exterior-weatherstrip.

1. Remove the nut and the rear window stabilizer.

1. CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
   NOTE: Lower the window to access the rivets.
   Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.

1. Remove the rear door window glass.

1. To install, reverse the removal procedure.

SECTION 501-05: Interior Trim and Ornamentation 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Rear Door Trim Panel Removal and Installation

1. Remove the rear door trim panel screws.

1. NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door.
   NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel.
   Remove the rear door trim panel.
   • Disconnect the window regulator control switch electrical connector.

1. To install, reverse the removal procedure.

1. Raise and support the rear door window glass to the full up position.
2. Remove the interior door handle.
3. Remove the rear door speaker.
4. Remove the water shield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
8. Installation is the reverse of the removal procedure, noting the following:
   • Cycle the door glass to make sure of engagement of the drive mechanism.
   • Remove the rear door window glass-to-regulator bolt or rivet.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
   • Secure the rear door window glass in the full UP position with tape.
   • Disconnect the window regulator motor electrical connector.
   • Remove the 2 window regulator nuts.
   • Remove the 3 window regulator motor bracket nuts.
   • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
   • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
   • Connect the window regulator motor electrical connector.
   • Remove the tape securing the rear door window glass in the full UP position.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
   • Install the window regulator motor
   • Remove the window regulator assembly.

Remove the window regulator motor