DOES MY DURANGO HAVE ABS IN THE FRONT? DOES IT HAVE AN UPPER AND LOWER BALL JOINT?

Lower you can do fairly easy. Upper, a bit tougher.For the upper you will need a spring compressor.

SponsoredShop for Whats the part number fo... on Google
Moog K500007 Lower Ball Joi...
$33.26
Jet.com Moog K6117T Ball Joint
$27.79
Walmart Parts Master K9385 Lower...
$10.97
Jet.com Control Arm W/ball Joint Fr...
$59.70
eBay Ball Joint ? Lower/Upper...
$22.95
EPI Performa... Search Results

Ball Joint - Lower at AutoZone.com - Best Ball Joint - Lower ...

www.autozone.com/suspension-steering-tire.../ball-joint-lower

AutoZoneShop for Ball Joint - Lower products with confidence at AutoZone.com. Parts are justpart of what we do. ... Duralast/Ball Joint - Lower, Part Number: FA1490 ...

Dodge Stratus Ball Joints ' eBay

For your problem,check out this few help links.

Click the link below to go through its procedure:----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html------- How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html------- How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html------ How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html----------- How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html--------- Lower Ball Joints replacing on Mitsubishi car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
-------------These details will help.For more help,keep updated,with car brand,model and year.Thanks.Helpmech.

Wheel Spindle, F-150, F-250, F-350
Removal

1. Raise the front of the vehicle and install safety stands.
   

1. Remove the wheel and tire assembly. Refer to Section 04-04 .
   

1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
   

1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
   

1. Remove the rotor from the front wheel spindle (3105).
   
   
   
   
   
   Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
   (57-75 Lb-Ft) B - Tighten to 68-92 Nm
   (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)

1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
   

1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
   

1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
   

1. Remove the cotter pin and castellated nut from the lower ball joint stud.
   

1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
   

1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
   

1. CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
   Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
   

1. Remove the front wheel spindle and ball joint from the axle.
   
   

Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal

1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
   

1. NOTE: Lower ball joint must be removed first.
   
   Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
   

1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
   

1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
   
2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
   Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.
   
   
   Installation
   
   1. CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.
      
      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.
      
      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
      
   1. Turn forcing screw clockwise until ball joint is seated.
      
      
      
      
   

Well depending on make and model, if the vehicle has front struts, there is no upper ball joint, the top of the suspension is the strut and the bearing plate at the top, it only has a lower. On most other Ford vehicles, most of the time it is the lower ball joint that goes bad because it is the load bearing ball joint. Please list the make and model of vehicle you are wondering about.

Removal Steps

1. Torsion bar

2. Wheel speed sensor

(if equipped with ABS)

3. Back plate

4. Lower ball joint

5. Upper ball joint

6. Knuckle assembly

7. Oil seal

8. Thrust washer

9. Needle bearing

10. Knuckle

Installation Steps

10. Knuckle

9. Needle bearing

8. Thrust washer

7. Oil seal

6. Knuckle assembly

5. Upper ball joint

4. Lower ball joint

3. Back plate

2. Wheel speed sensor

(if equipped with ABS)

1. Torsion bar

most likely on these is the ball joint

using one person to bounce on the front end, use something like penetrating oil to squirt on suspet components

It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

If it's the upper ball joint, just the ball joint can be replace, but if it's the lower ball joint the complete lower control arm will have to be replace, arm will come with new ball joint and bushings.

Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
   
2. Raise and support the vehicle.
   
3. Remove or disconnect the following:
   
   • Tire and wheel
     
   • Wheel hub and bearing, if necessary
     
   • Outer tie rod retaining nut
     
   • Out tie rod from the steering knuckle using a suitable puller
     
   • Brake hose bracket retaining bolts and bracket
     
   • Upper control arm-to-steering knuckle pinch bolt and nut
     
   • Upper control arm from the steering knuckle
     
   • Lower ball joint retaining nut
     
   • Steering knuckle from the lower control arm using a suitable ball joint removal tool
     
   • Steering knuckle from the vehicle
     
   • Lower ball joint flange with a chisel
     
4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
   

To install:

1. Install or connect the following:
   
   • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
     
2. Remove the tools from the lower control arm.
   
   • Tools J 9519-E and J 45105-1 to the lower ball joint
     
3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
   
   • Steering knuckle to the lower control arm
     
   • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
     
   • Upper control arm to the steering knuckle
     
   • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
     
   • Brake hose bracket to the steering knuckle
     
   • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
     
   • Outer tie rod to the steering knuckle
     
   • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
     
   • Wheel hub and bearing, if removed
     
   • Tire and wheel
     
4. Lower the vehicle
   
   • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
     
   • Wheel center cap, if removed
     
5. Check the front wheel alignment.