Belt install diagram 3.4 liter

The video shows the whole thing on a LeSabre. This link shows the belt routing and where to get a new belt.

https://www.google.com/search?q=2005+buick+rainier+serpentine+belt+diagram

Search Results

images for diagram on how to replace a serpentine
How To Install Replace Serpentine Belt Oldsmobile Alero 99 ...? 3:33https://www.youtube.com/watch?v=jkzXTt43uwwFeb 9, 2012 - Uploaded by 1A Auto PartsHow To Install Replace Serpentine Belt Oldsmobile Alero 99-04 2.4L .... There should be a belt routing diagram on the frame rail or under side ...serpentine belt install 3.1/ 3.4 v6 - YouTube? 4:00https://www.youtube.com/watch?v=GYoWuvEZ2DcMay 6, 2013 - Uploaded by JoeTheAutoGuythis a serpentine belt install video on a 3.1 liter gm v6 , 3.4 liters are the same in ... Replacing the alternator or serpentine on anyOldsmobile Alero 99-04 3.4 Liter ... Serpentine Belt Replacement 1995-2005 Chevrolet Cavalier .

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

Draw your own before you take the old belt off. Its easy and saves trying to find a diagram that might not even be right for your model .

If you have the ac turned off the clutch on the front of the compressor should disengage. Then the ac pulley will spin freely and you can drive until you save up for a new compressor. You may want to save up they are about 3 to 400 bucks plus installation which is about 300.

The serpentine belt routing diagram for 2000 Audi A6 2.8 liters V6 engine:


CS = Crankshaft
F = Fan pulley
Gen = Alternator
T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering

Here's the diagram you asked for for the 95 Buick LeSabre

There is an idler pulley just below the alternator in the back of the engine, passenger side. Loosen by using a socket wrench to loosen the central bolt (there are two, one upper and one lower, you want the UPPER bolt). You don't need to remove, just loosen to relieve tension on the belt. The diagram for the belt is actually on a little plastic plaque on the front left of the engine.

I had to do that once, but it was on an older vehicle that AC was optional. Probably your best bet would be to see if you can wrap the belt on there, but bypass the AC pump. Then just mark the belt with a white marker to get the length you need. Take it to the parts store and have them measure it with their guide. They should be able to find you one that length. If a Rendezvous came without AC, you could just go in and ask for the belt for one without AC, but I don't think they did.

look around under the hood , on the underside of the hood, sometimes the belt routing diagram is on a sticker also check a Chiltons Manual sold at auto pARTS STOReS or on the web