Location of purge valve 2001 ford mustang gt 4.6 engine

https://www.youtube.com/watch?v=wZ5QCJtzhLA

mages for 4.6 Engine valve train in 2008 Ford Mustang Gt


More images for 4.6 Engine valve train in 2008 Ford Mustang Gt

2005-2009 Mustang Cylinder Heads & Valvetrain ...

www.americanmuscle.com/mustang-valvetrain-0508.html
They help your motor breathe better and also make sure your Mustang gives top-notch throttle response. ... 2005, 2006, 2007, 2008, 2009 Mustangs; V6, GT, Bullitt, Shelby GT500, ... 2005-2009 Mustang GT Cylinder Heads & Valvetrain Components ... (6).Ford Racing SOHC 3V 4.6L Head Changing Kit (05-10 GT) $76.00.

Mustang Camshaft Facts & Technical Information ...

www.americanmuscle.com/camshaft-tech-guide.html

Code 1457 is Purge Solenoid Valve Low. Check your emission system for a leak

the purge valve is located in the engine compartment. http://www.allfordmustangs.com/forums/attachments/5-0l-tech/127072d1302466404-1989-gt-codes-wire-identification-purge-valve.jpg Good Luck!

Look on the Fuel rail on the left and right side, there is usually a cap that looks like a valve cap or a tire. It will have a needle valve inside just like a tire valve, Beware, when you purge the fuel system, make sure the engine is not running or the key is on and make sure the engine is cool. It will spray fuel. Take a blunt end object and push down on the valve pin, be sure to cover your hand with a rag so it don't spray fuel in your face or on your skin. This should purge the fuel system. It may take a couple tries to get all the air out. Allow the fuel to disapate and dry up before you start the engine. This could cause a fire if there is raw fuel laying in the crevises of the engine. An air hose with a blow valve is helpful to dry up the fuel. Again, cover your face or wear safety glasses. I hope this is helpful, I own a 2003 mustang GT my self.

For 2001 Ford Mustang 3.8L SFI 6cyl engine, with which your specific vehicle is equipped, can be most easily identified by the Vehicle Identification Number (VIN), located on either the VIN tag, mounted in the upper left-hand corner of the instrument panel, or on the vehicle certification label, located on the driver-s side door pillar. The engine identifying code is the 8th digit of the VIN. The engine VIN codes are as follows:



FIG: Engine identification codes may also be found on a label affixed to the left side rocker arm cover

4-3.8L SFI (OHV) engine N-4.0L SFI (SOHC) engine H-4.6L SFI (SOHC) engine V-4.6L SFI (DOHC) engine
X-4.6L SFI (SOHC) engine

Hope helps.

try disconnecting positive cable for 5 min and rehook to reset computer. berrydalewolf

IT ALMOST SOUNDS LIKE YOU MAY HAVE A VACUUM LEAK SOMEWHERE. USE A LENGTH OF RUBBER HOSE AND HOLD IT UP TO YOUR EAR TO PIN-POINT THE LOCATION OF A VACUUM LEAK. HOPE THIS HELPS. LET ME KNOW PLEASE. THANK YOU IN ADVANCE FOR AN HONEST RATING AND THANKS FOR USING FIX-YA. P.S. EGR VALVE IS VACUUM ACTUATED

ECT is located to the right(passenger side) of the alternator in the intake manifold.
PCM is located behind the right(passenger) kick panel under the corner of the dash.

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett