Where is anti-theft control module located? - 2003 Kia Sedona

Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• transceiver module
• PATS control module (located behind the passenger side air bag module)
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network

Anti-Theft - Passive The passive anti-theft system (PATS) contains the following components:

• anti-theft indicator
• encoded ignition key
• PATS transceiver
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network

Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• transceiver module
• PATS control module (located behind the passenger side air bag module)
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network

it's software programmed into the control modules on the vehicle . Depending on the make vehicle , could include a theft deterrent module , body control module and the PCM - engine computer .

Without a key with anti-theft transponder inside your not starting anything . Your best bet call mobile lock smith . Anti-theft system ,software programmed into all module's involved in starting the vehicle .
The vehicle theft deterrent (VTD) system functions are provided by the theft deterrent control module. The VTD system prevents vehicle operation if a learned Passkey III (PK3) ignition key is not used to start the vehicle. Vehicles with steering column mounted ignition switches have the exciter integral with the theft deterrent control module which is located within the steering column. Vehicles with instrument panel mounted ignition switches have exciter modules separate from the theft deterrent control module with the vehicle wiring harness connecting the two. The PK3 key has a transponder embedded in the plastic head of the key. The exciter is an antenna which is made up of wire coils which surround the ignition lock cylinder. The PCM enables engine starting when it receives a learned fuel enable signal from the theft deterrent control module. The components of the VTD system are as follows:

Explain anti-theft fuse box ! what do you think this is ? There is an anti-theft system on your vehicle , called PATS - passive anti theft system .Sorry , but there is not anti-theft fuse box .
Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• PATS transceiver module
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network

There are several computer modules involved in your antitheft and security system.
There is the Driver's door module, the right front door module, the right rear door module, the left rear door module, the dash integration unit, the rear integration unit, the instrument panel cluster, the theft deterrent module, the theft deterrent exciter module, the body control module and the powertrain control module. These are all networked together to form the perimeter security and anti-theft system.

Any problems you may be having with this system should be properly diagnosed. Diagnosis of this system must BEGIN with a complete scan of the onboard computer network so that fault codes can be retrieved. and the computer data checked and verified. This is the only way to correctly determine which part of the system is malfunctioning.

Wiring schematics are not designed to give you the location of these components. They only show the wiring connections that are made between them.

What exactly are you trying to fix?

Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:

• protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
• monitors the status of the ignition key lock cylinder.
• is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
• when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
• protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
• triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.

Once triggered, the system responds by:

• flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
• sounding the horn (13832).
• disabling the starter circuit until the system is disarmed.

---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module

• The remote anti-theft personality module is located behind the instrument panel (04320).
• It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
• The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.

-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove radio. Refer to Section 15-01 .
   

1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
   

1. Lower glove box.
   

1. Remove two remote anti-theft personality module bracket retaining screws.
   

1. Disconnect electrical connectors and alarm and lock system antenna (15603).
   

1. Remove remote anti-theft personality module and bracket.
   

1. Remove remote anti-theft personality module from mounting bracket.
   

Installation

1. To install, follow removal procedure in reverse order.
   

1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).
   
   

Components The system is composed of the following components:

• remote anti-theft personality (RAP) module with integral antenna
• alarm indicator LED
• door lock cylinder switch RH, door lock cylinder switch LH
• liftgate door lock cylinder switch (220A40)
• hood switch (part of windshield wiper motor wiring (17A477))
• ignition lock anti-theft switch (19A438)

The following vehicle components are also used by the anti-theft alarm system:

• generic electronic module
• power door lock switch (14028)
• door open warning lamp switch (14018)
• autolamp relay (14N089)
• horn relay and bracket (13853) and horn (13832)
• low beam headlamps
• rear lamps (13404) and parking lamps (13200)
• starter relay
• door lock relays
• keyless entry remote transmitter (15K601)

--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:

1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
2. Unlock any door with a key.
3. Turn ignition switch to RUN or ACC.
4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.

------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:

• Open any door or liftgate.
• Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
• Dislodge the ignition key lock cylinder.
• The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.

When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

• low beam headlamps
• parking lamps
• horn
• THEFT indicator

The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Passive Anti-Theft System (PATS) Module:

• located behind the integrated control panel.
• works in conjunction with PCM to enable or disable engine start function.
• failure of the PATS or communication to the module may result in a no start condition.
• if communication to the PATS module fails during diagnostics, refer to Section 13-11B .