What is engine troubleshooting code p0205 mean on a 1999 nissan altima 2.4

francisco navarro

• 241 Answers
• Posted on May 15, 2008

SOURCE: Replacing a starter for a 1999 Altima

1. Disconnect battery ground cable.
2. Disconnect starter wiring from starter.
3. Remove starter retaining bolts and the starter.
4. Reverse procedure to install.

SOURCE: whate is code 1400 and 400 in nissan altima 2001.

P1400 DPFE Circuit Low Input
P0400 Exhaust Gas Recirculation Flow Malfunction

These codes represent a fault in the Auxiliary Emission Controls. Here's a brief describing of the EGR valve. The EGR stands for exhaust gas recycling valve. During cruising speeds, the valve opens allowing exhaust into the intake manifold. The purpose of this is to cool the temperature of the combustion inside the cylinder as the spark plug fires. This in turn, lowers emissions. If the EGR is stuck in either direction(open/closed), it can effect the idle of your vehicle and can stall it out at times. it can also trip the engine light as well. Good rule of thumb is to clean out the carbon out of the intake manifold thoroughly before you install a new EGR. this will prevent the engine light form coming on once more. if the carbon build up is high, chunks of it will jam the EGR, causing it to fail over and over.


Please rate and god bless.

SOURCE: nissan quest 1999 engine light codes P0325 &

P0325 is for the knock sensor.

P1105 is for the manifold absolute pressure sensor (MAP).

In either case diagnostic tests need to be performed to rule out faulty sensors or if something else is causing the sensors to give the computer inaccurate information.

SOURCE: receiving engine code p0420 on my 2005 altima 2.5 s

A p0420 code indicates a Catalytic System efficiency failure, Bank 1.
Basically, the computer is seeing reduced efficiency of the catalytic converter or one of it's components (such as an 02 sensor)

There may be a few root causes, such as a faulty oxygen sensor, faulty coolant temperature sensor, faulty converter, Large exhaust leak, or retarded (slow) timing.

ZJ Limited

• 17989 Answers
• Posted on Apr 05, 2010

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine