Timing marks 2006 ford focus 2.0tdci

SOURCE: 2000 ford focus twin cam timing

please helpme i need timing marks for ford focus 2000 16 valvs

SOURCE: cannt find tims marks on 2000 ford focus twin cam

there are no marks on the cams line the crank up you should see marks on it and on the cams take a flat piece of steel like a flat file and put it on the end of the cam shafts the side near near the drivers side ounce you take a look youll see what i mean this should help you out

SOURCE: 2001 Ford Explorer 4.0 SOHC no timing marks on cam or chain

get a haynes manual and look up camshaft replacement..its worth the 30 bucks

SOURCE: 1999 Ford Expedition 5.4L Timing chain setup

.

1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.

1. Remove the crankshaft sensor ring from the crankshaft.

1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.

1. Using the special tool, position the crankshaft as shown.
   

1. Install the special tool.

1. NOTE: LH shown; RH similar.
   Remove the two bolts, the timing chain tensioner and tensioner arm.

1. Remove the LH and RH timing chains and the crankshaft sprockets.
   
   • Remove the special tool from the crankshaft.
   • Remove the timing chains from the camshaft sprockets.
   • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.

1. CAUTION: The bolts are different lengths and must be returned to their original location.
   NOTE: LH shown; RH similar.
   Remove the bolts and the timing chain guides.

1. CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
   CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
   Compress the tensioner plunger, using an edge of a vise.

1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.

1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.

1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.

1. Remove the tensioner from the vise.

1. NOTE: There are 61 links in the timing chain.
   If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.

1. Install the timing chain guides.

1. Using the special tool, verify correct crankshaft position.
   • Remove the special tool.

1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
   If removed, install LH and RH crankshaft sprockets.

1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.

1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.

1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.

1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.

1. NOTE: LH shown; RH similar.
   Position the tensioner arms and tensioners, and install the bolts.

1. Remove the tensioner retaining clip.

1. As a post-check, verify correct alignment of all timing marks.

1. Remove the special tool.

1. Position the crankshaft sensor ring on the crankshaft.

1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.

SOURCE: diagram for timming belt on 2002 ford focus 2.0ltr

there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Testimonial: "thank you"