2009 ford focus windshield washer reservoir cracked and leaking

Here's the fuse box diagram for your vehicle
https://ricksfreeautorepairadvice.com/2009-ford-focus-fuse-diagram/

Have you checked to see if you have a cracked reservoir ? Could also be a hose that is cracked or maybe the washer motor came off the reservoir.

could be a bad rubber grommet around the washer pump
most likely a cracked plastic reservoir

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.

1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
   Remove the bolt and the windshield washer reservoir filler neck.

1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .

1. Remove the foam filler and remove the retainer.

1. Remove the 2 screws and the accessory drive splash shield.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the nut, 2 bolts and position the A/C accumulator aside.
   • To install, tighten to 9 Nm (80 lb-in).

1. Unclip the A/C lines from the inner fender well.

1. Drill out the rivet and remove the bracket.

1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
   • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).

1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.

1. Disconnect the electrical connector from the windshield washer pump.

1. Release the wiring harness from the reservoir, and remove the washer reservoir.

1. To install, reverse the removal procedure.

Check the hose to it

The Tank maybe cracked
& have to be replaced

windshield washer reservoir has a crack in it or look for leaking washer reservoir hose leaking fluid.

Ford Focus engine diagram Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V

1 - a tank of the hydraulic booster of a steering; 2 - a plug mouth oil-jellied; 3 - a tank of a working liquid of a braking system and clutch; 4 - the assembly block of safety locks and the relay; 5 - an air filter; 6 - a windshield washer reservoir; 7 - the accumulator battery; 8 - the identification tablet; 9 - a measuring instrument of level of oil; 10 - an expansion chamber of system of cooling.

Ford Focus engine diagram Ford Focus engine diagram - turbo-diesel of 1,8 l Endura-DI Ford Focus engine diagram - turbo-diesel of 1,8 l Endura-DI

1 - a tank of the hydraulic booster of a steering; 2 - a plug mouth oil-jellied; 3 - a tank of a working liquid of a braking system and clutch; 4 - the assembly block of safety locks and the relay; 5 - an air filter; 6 - a windshield washer reservoir; 7 - the accumulator battery; 8 - the identification tablet; 9 - a measuring instrument of level of oil; 10 - an expansion chamber of system of cooling.

Remove the windshield washer reservoir and give it a good cleaning with a mixture of 1 part bleach and 3 parts water. You may be able to clean it without removing the reservoir by flushing it throughly and the cleaning it while still on the vehicle with the bleach mix. After it is throughly cleaned put a bleach mix in the reservoir and disconnect the hoses from the spray nozzles and run the washer until the hoses are clean. Use a needle to clean out the nozzles, and the connect the hoses and run the washer until the nozzles are clear. Remove the bleach mix and then fill the reservoir with a commercial windshield washer fluid. I recommend Rain X.

I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:

• Windshield washer reservoir, below the front left-hand fender
• Washer pump, on the outside of the washer reservoir
• Two washer nozzles on the hood/bonnet, adjustable.

---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles

1. Remove the windshield washer reservoir filler neck.

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the right-hand fender splash shield (wheel shown removed for clarity).

1. Remove the washer reservoir.
   • Disconnect the electrical connectors.
   • Pull off the hoses.

1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
   1. Disconnect the electrical connector.
   1. Disconnect the hoses.
   1. Lift out the pump.

check under your washer reservoir.