Question about 1994 Oldsmobile Cutlass Supreme

2 Answers

Need to know cylinder head bolt torque specs

I have 1994 Oldsmobile Cutlass Supreme with 3.4 Liter engine. I am replacing the head Gaskets and need to know the proper torque specs for the cylinder head gaskets. My manuel only gives the initial settings. I have the tighting sequice, need the foot pounds.

Posted by on

  • 1 more comment 
  • Anonymous Mar 13, 2014

    torque inch pound for head bolts of holden baina 2003?

  • Anonymous Mar 13, 2014

    need to know procedure to remove and replace head gasket on 2005 ford freestar

  • Anonymous Mar 19, 2014

    need torque spec

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 230 Answers

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): need to know cylinder head bolt torque specs - clearpixel.gif Foot pounds (Final torque) need to know cylinder head bolt torque specs - clearpixel.gifoads/images/clearpixel.gif" alt="clearpixel.gif" class="h_mi" /> Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplacneed to know cylinder head bolt torque specs - clearpixel.giflled to obtain properneed to know cylinder head bolt torque specs - clearpixel.gifmg src="/uploads/imagneed to know cylinder head bolt torque specs - clearpixel.gifgif" alt="clearpixel.gif" class="h_mi" /> clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Want to know the engine head torque 14b.

Posted on Oct 30, 2017

  • Davley Safamo
    Davley Safamo Oct 30, 2017

    Want to know the engine head torque 14b.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the specs for the intake and head tork settings


cylinder head bolts are torque to yield bolts and are not recommend to torque them a 2nd time you should replace the bolts.

cylinder head blots.

step 1. 44 ft.lbs.

step 2. additional 95 degrees

lower intake bolts

115 in. lbs

upper intake bolts

18 ft. lbs

Apr 23, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

What is the torque settings on a 3.4 liter engine 94 camaro. replaced the heads and gaskets


Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

I hope this helps you and good luck

Mar 25, 2011 | 1994 Chevrolet Camaro

1 Answer

I have a 1994 Olds Cutlass Supreme overheating


If it's the water pump, you should be able to see it dripping just behind the pulley. The seal on the water pump is usually what goes. If there is antifreeze drips all over the front of the engine, and it drips a bit after you shut it off, it likely is the water pump.
If it runs poorly when you first start it in the morning, however, you could still have a head gasket problem. If that is the case, you will see a lot of white exhaust, which is the cylinder blowing the antifreeze out. One thing you can do is run it with the rad cap off, and see if it continues to bubble. If it does, then your head gasket is leaking. I am assuming it is a V6, so keep in mind that you have 2 head gaskets. The other oine could be gone now if it wasn't replaced.

Apr 05, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Replaced intake on 88 oldsmobile cutlass. now running rough


ticking means timing is off. Or possibly you havent torqued the manifold on properly. 18 Ft-Lbs torque

Mar 18, 2010 | 1988 Oldsmobile Cutlass Supreme

1 Answer

Where are the gaskets on a 1994 oldsmobile cutlass supreme


valve covers,1/2 hour each, oil pan 1 hour,head gaskets 7 hours,transmission pan1 hour ,intake 5 hours,or exhaust manifold gaskets.4 hours

Oct 23, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

94 cutlass supreme smoking and stalling


That sounds like valve guides or valve guide seals.When they wear they the car blows smoke out the exhaust.Especially after leaving from a stop

Oct 14, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1994 old cutlass ciera 3100 blown head gasket.


Get a Chilton's book on the car. It will take you thru the whole job, and give you the torque specs for putting it back together. You will need a torque wrench, foot pounds, and a good socket set.

May 04, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Engine overheating-----1994 Olds Cutlass Supreme 3.4 liter v/6


There seems to be an air pocket or no antifreeze in engine block. Try this method disconnect upper radiator hose and pour water directly into hose down into engine block until it full. when its filled reconnect hose and fill up radiator. as the vehicle warms up open bleeder valve on the thermostat housing and release air from system. open slowly and BE VERY CAREFUL WATER WILL BE HOT, bleed until you get a steady stream opening and cosing valve. However if all of this don't work. You may have a bad pump. Good Luck

Dec 27, 2008 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

3,370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...