Have no rear brakes new master cyl. all new pads line even changed the abs mod. front will bleed out back will not new wheel cyl, no fluid back there
SOURCE: brake repair
i had a problem once that the rear drums were turned to far out and caused me to have to pump and also have a spongy pedal....just a thought
SOURCE: 1994 Cavalier -replaced master cylinder-no pressure to rear brake
The most common bleeding procedure is to bleed the ABS brake furthest from the master cylinder first, then bleed the other brake that shares the same hydraulic circuit (which may be the other rear brake on a rear-wheel drive car, or the opposite front brake on a front-wheel drive car or minivan). After these have been bled, you then bleed the other brake circuit starting with the furthest brake from the master cylinder.
Air can be very difficult to remove from an ABS modulator assembly because of all the nooks and crannies inside the unit. The modulator may have eight to 10, or more, ABS/traction control solenoid
valves, plus various check valves and dead-end ports. Some ABS modulators have special bleed screws to help you vent the trapped air when bleeding the system. Others do not and require the use of a scan tool to cycle the ABS solenoids while you bleed the system. 1. To bleed the isolation valves in the modulator, there are two bleeder screws. Start with the one toward the engine. Turn the ignition on and apply light pressure on the brake pedal. Open the bleeder screw and allow the fluid to flow until clear. Close the screw and do the same at the second bleeder screw. 2. Depressurize the accumulator by pumping the pedal 40 times with the key off. Wait about two minutes for the brake fluid to de-aerate, then refill the fluid reservoir with DOT 3 brake fluid. 3. Now you can bleed the boost section. This is done by applying moderate pressure on the brake pedal and turning the ignition on for three seconds, then off. Repeat this a total of 10 times. Make sure the pedal feels firm when you have finished, and give the car a road test to make sure the brakes are working properly.
SOURCE: how do you bleed the abs unit on a 1997 chevrolet truck
start by bleeding the master cylinder bleed the line closest to the fire wall, then proceed to the right rear wheel, left rear wheel, right front wheel, and then the left front wheel.
SOURCE: 1999 Chevy Tahoe- Soft Brake Pedal
Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.
SOURCE: I have a 1997 chevy cavalier. I replaced wheel
sometimes if you leave the bleeder screw open it will gravity bleed the cylinder.Make sure master cyl is full and do one wheel at a time.I have seen this work, I have done it.
Fig. 1: Loosen the front brake line in order to bleed the master cylinder
Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid
Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system
Hope this helps to solve it; remember to rate this answer.
225 views
Usually answered in minutes!
×