Seagate CHEETAH - Recent Questions, Troubleshooting & Support

mostly cheetahs eat YOU if you get to close

Every computer beeps on boot up . there are several beep codes that can help with faults.

As far as I know they range from 73 GB to 300 GB.

browse over to http://www.seagate.com/internal-hard-drives/enterprise-hard-drives/hdd/cheetah-15k/ and select the options on the right hand side that match your drive. That will give you the model number. Then go to https://apps1.seagate.com/downloads/request.html and fill in the model and serial numbers to get the right software drivers.

Test your PSU or replace it if your power supply units fan is not working your PSU is faulty

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect/ boot up a computer hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your "((MOTHERBOARD TO YOUR HARD DRIVE))" make sure they have a secure connection and are not faulty or just replace them they could be faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electrical extensions or just replace them they could be faulty a computer needs its connections to continue its cycle and have an end so any faulty leads will end up with a computer error even something as small as a faulty electrical extension or fan lead can cause this problem:

follow the troubleshooting procedure a computer needs all of the data and electrical current to travel through every working device and to have an end to be able work properly

a motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive if its a flat ribbon 40 pin type IDE replace it this will be the first to fail check all electrical extensions make sure they are securely seated even the cd/dvd floppy drives need to have current go through make sure these drives are working hope this helps also it could be a dirty computer: clean all of the dust from your computer you could use a vacuum cleaner but whatever you use make absolutely sure there is no moisture gets to anything in your computer

also check the Cmos battery and computer ram make sure they are securely seated

hope this helps:

During the boot process you will see on the screen to press a certain key to enter setup Press and hold that key during the boot up process to enter BIOS the scroll down to advanced bios features press enter change your first boot device to IDE-1 means Pri slave escape then press f10 to save to cmos to restart you will have to have master with slave set up you can find the jumper location next to the power on a hard drive and the settings for plastic jumper location is usually printed on the top of a hard drive IDE-0 means Pri master ? IDE-1 means Pri slave ? IDE-2 means Sec master ? IDE-3 means Sec slave ?

? single or master :::::

master with slave ::'::

???????????????? slave? :::':

note the plastic jumper is

Welcome to Fixya

Try to format the drive from the disk manager then try to install XP again.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

myoung331

If the drive is not being detected properly then ether the SATA port you have the drive connected to does not support the drive or you need to install updated SATA drivers for your motherboard to fully see the drive. I myself ran into this the other day when I upgraded the hard drive in my computer.

If you are not sure if it is supported and/or having trouble finding drivers let me know the make and model of your motherboard.

Issken
http://www.fixya.com/users/issken

Detailed steps to manage backup disk space

To delete old backups on Windows 7/8/10 using AOMEI Backupper, you need to set up Backup Scheme during the process of creating a backup. When your backup versions exceed the number of backup images files, AOMEI Backupper will delete older backup automatically. Step 1: Connect your Seagate Backup Plus drive or Central hard drive to the computer and make sure it can be detected by your computer. Step 2: Download AOMEI Backupper Professional, install and launch it. Step 3: Click Backup and File Backup subsequently Step 4: Choose the files and folders you want to backup and pitch on a path for it. Then, Click Schedule option and select Schedule Settingsfrom the following window. Step 5: Click Scheme option, tick Enable Disk Space Management and select whatever Scheme you need from the drop-down menu. Then, back to the main page of File Backup and click Start Backup. After that, your older backup will be deleted automatically when your file backups exceed the versions of backup image files.

For the Seagate hard disk model ST3120827AS, the TVS diode is typically located on the circuit board (PCB). TVS diodes are designed to protect electronic circuits from voltage spikes and transient events. They are usually small, with two leads, and look like small cylindrical or rectangular components.To locate the TVS diode on the circuit board, you may need to refer to the hard drive's datasheet or schematic diagram, if available. Additionally, you can try searching for online resources or forums where individuals share information about hard drive components and their locations.Regarding the Cisco Nexus Network Switch , it's important to note that specific details about the internal components, including the location of TVS diodes, may be proprietary and not readily available in publicly accessible documents. For detailed information about the switch's internal components, you may need to refer to Cisco's official documentation or contact Cisco's supporthttps://www.serverblink.com/n3k-c31108pc-v-cisco-nexus-network-switch/

Go to the link below for a program that may get your data recovered - OR do a search on Google for "hard disk recovery" - depends on where you are - US, Canada - it will cost about $200 dollars to get your data back

http://www.stellarinfo.com/disk-recovery.htm

Did you initialize it?

Hi, Please put your computer into safe mode before attempting to connect to the hard drive again. Safe mode turns some feature off when activated so whatever program is forcing the shutdown might have be paused when connecting to the external hard drive. Also, try connecting the hard drive to a non-laptop intermediary device and then connecting that device to your computer and attempting to access the hard drive folder within the intermediary drive. Thank you.

when your music starts to download a BROWSE option should open you can select your hard drive or a folder in my documents or once its downloaded you could right click select copy and then paste the music into the folder or select the music hold the mouse and drag and drop it into the folderhow to make a folder right click in my documents select new folder you can name it then My Music

hope this helps

http://www.filehoo.com/download/Partition-Magic-8,0.aspx when you download partition magic you will have the option to make rescue to disks to boot from make these disks then change your first boot device your to floppy drive this will give you options to partition then partition only the good sectors of your hard drive and install an operating system to the good partition Partition Magic 8.0 descriptionPartitioning your hard drive plays an essential role in maintaining your computer-preventing conflicts, protecting data, improving efficiency, and increasing performance. PartitionMagic allows you to create, resize, merge and convert partitions without destroying data. Award-winning PartitionMagic Pro from Symantec is a leader in hard-drive partitioning software. PartitionMagic Pro allows you to create, resize, move, and convert partitions without destroying your data. You can quickly and easily create partitions, which can act as file drawers on your hard disks for storing valuable information such as data files, applications, and operating systems. Storing information in separate partitions helps you organize and protect your data, safely run multiple operating systems, and reclaim wasted disk space. i have used this and found it a very good program and is easy to install hope this helps you

Should be careful with the data file deposited on the Seagate external hard drive. your Seagate external hard drive might be dead or corrupted. In this situation, you might need to rely on data recovery software to get back data and files on the dead Seagate external hard drive. So you can rely on data recovery software to get back lost data and files when the Seagate external hard drive is dead and inaccessible. Data recovery hong kong technician provide the Ontrack EasyRecovery data recovery services are able to recover data and files from accidentally formatting, corruption, virus attack, dead, system crash under different situations Seagate external hard drive on Windows Computer. This data recovery software allows you to deep scan the dead Seagate external hard drive so as to find out almost all lost files with original quality in a short time. You can also rely on this software to recover files from dead/damaged Seagate external hard drive. The software supports to get more recover: Seagate External hard drive, data file, documents, PDF, Excel, photos, music, and videos any HFS, HFS, FAT, ExFAT, and NTFS format based data and file and more. It will recover data and file from all external storage devices that can be recognized by your Windows PC Computer/Laptop. Hope this helps you get to recover all your lost data and files from your dead Seagate External hard drive.

TRY LOOKING FOR TIGERDIRECT .COM THEY SELL STUFF FOR COMPUTERS

Hi i have just looked into need to upgrade your firmware please read this
Seagate products are run by firmware. Having the latest firmware can improve performance and or reliability of your product. Seagate recommends applying new firmware to enhance the performance and or reliability of your drive.
Like any software, firmware is improved over time and problems are also fixed. Every drive family has a couple of firmware releases during the life of the product. Please check in regularly to determine if new firmware is available for your drive.

As new firmware becomes available for other products we will make note of it here. At this time, we have firmware available for Barracuda 7200.12, DiamondMax 23, Barracuda LP, Barracuda 7200.11, Barracuda ES.2 (SATA) and DiamondMax 22 drive families.
If newer firmware is available for your drive, it will reflect the improvements we have engineered for the latest manufacturing. Firmware for legacy products will be the final release from manufacturing. Please note that Seagate does not offer details about specific firmware.

Until recently, firmware updates for typical desktop and laptop computers were difficult and somewhat risky. This situation, in part, was based on a lack of friendly firmware download tools and operating system limitations. This situation has improved and Seagate now offers firmware updates as a routine matter for the general support of your Seagate drive.

/> If you are troubleshooting a system or OS problem, you should not consider firmware updates until after exploring more typical troubleshooting steps like file system error checking and anti-virus scanning.
Please use the following links and instructions below to determine if firmware is available for your product. If firmware is available, we recommend that you make a back up before running the actual update and that you read and follow all instructions, cautions and warnings that may be displayed.

Follow these steps to determine if a firmware update is available for your drive:

1. Click here for instructions on how to determine your model and serial number.