Raymarine Boating - Answered Questions & Fixed Issues

According to a post on the Raymarine forum, this error message could indicate an issue with either the steering, the drive unit, the rudder reference unit (if fitted), or the course computer . The post suggests a few tests that you can do yourself to figure out which item is causing the issue. I suggest that you try the following steps: Check the connections between the ST8002 SmartPilot and the other components of your autopilot system. Check the calibration of the ST8002 SmartPilot and the other components of your autopilot system. Check the hydraulic fluid level and the hydraulic pump pressure. Check the hydraulic pump motor and the hydraulic pump solenoid valve. If none of these steps work, I recommend that you contact Raymarine customer support for further assistance.

To connect your Garmin 741sx with your Raymarine ST 4000 using NMEA 183, you will need an NMEA 0183 interface cable to connect the two devices. Here are the steps to follow:

1. Obtain an NMEA 0183 interface cable that has the correct connectors for your Garmin 741sx and Raymarine ST 4000.
2. Connect one end of the NMEA 0183 interface cable to the NMEA output of your Garmin 741sx.
3. Connect the other end of the NMEA 0183 interface cable to the NMEA input of your Raymarine ST 4000.
4. Configure your Garmin 741sx to output NMEA 0183 data. Refer to your Garmin 741sx manual for instructions on how to configure NMEA output.
5. Configure your Raymarine ST 4000 to receive NMEA 0183 data. Refer to your Raymarine ST 4000 manual for instructions on how to configure NMEA input.
6. Once both devices are configured, the data from the Garmin 741sx should be transmitted to the Raymarine ST 4000 via the NMEA 0183 interface cable.

Question edited for clarity.Question moved from Cars and Trucks to Raymarine.Adjusting the display lighting The display has two distinct color palettes, for day and night operation. You can alsomanually adjust the backlight level.Note: The display lighting is a local setting and will therefore only affect the individualdisplay on which you are working.Day/night operationTo select the day/night mode of operationhttps://www.manualslib.com/manual/138190/Raymarine-C-Series.html?page=30#manual

The manual refers. Press CTRL+F, type 'set speed'. Press enter.

ST60 Speed Instrument OwnerTs Handbook - SV Zanshin

https://www.sv-zanshin.com > manuals > raymarin... PDF We are sure your ST60 instrument will give you many years of trouble-free operation. This handbook describes how to install and use the Raymarine ST60 Speed. 52 pages

Speed Calibration - Raymarine ST60 Owner's Handbook ...

https://www.manualslib.com > manual > Raymarine-St60 Speed calibration · 1. With the Calibration Run Length screen displayed, press the timer · 2. Set the length of the intended calibration run, using either the ...

• Speed Calibration - Raymarine ST60+ SPEED INSTRUMENT ...

  https://www.manualslib.com > manual > Raymarine-St6... Raymarine ST60+ SPEED INSTRUMENT Manual Online: Speed Calibration. ... Set the length of the intended calibration run, using either the timer button.

Hi, I have the same problem. Did you find an answer?

on the transom outside of the boat silicone the bolt holes

"Finally convinced him that **your** specs requiring the 4c cable at those lengths was correct" You know we are Fixya and not Raymarine? We just have a Raymarine category for handy filing of questions and answers. This question needs a factory service department technician on the phone. As a boat owner, who doesn't have radar, and reading your post carefully, I would suggest the connection at the top of the mast. It is far more hostile up there, and it has been up there a long time.

below the link for manual is below

Check with Raymarine. Model number would be of use. http://www.raymarine.com/view/?id=10125 Raymarine Manuals Documents

Look for map source in setting menu.

Make sure that your battery is in perfect condition. Low battery may trigger that alarm

Output on GPS should be connected to input on listening device.

Internal or external antenna? Any sources of electromagnetic interference or something blocking view to sky?

Raymarine a67 Installation And Operation Instructions Manual There you go. Click above link. Good luck. Semper Fi, Z

I am not familiar with your particular model autopilot, but I do know that Raymarine autopilots can be fussy. All must have a compatible gps feeding it, of course. All must have a rudder angle indicator if your auto pilot connects to the wheel or rudder instead of directly to the tiller. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_f6ca18ca1db028ed

Hi David. A little late, but the information you require can be found here: http://www.raymarine.com/view/?id=346 Hope it helps someone else out. -Steve Raymarine ST1000 ST2000 Tiller Pilots

You can probably find another control head on eBay... the ST6002 should also work, though it's smaller. The ST8002 is the same size but adds a knob meant for powerboats, but should also work. All three models are SeaTalk, which is what you need. The ST70 is also SeaTalk in addition to N2K, so I'd expect it to work.

It replaces the fluxgate compass and adds a few Moore sensors to the system, such as acceleration an deviation sensors to give a m?re intelligent data to the processor

I suggest you sell that before you have serious problems and no one will buy it. Yeah, that's what I would do... after all the two best days of a boat owner experience are the day you buy it... and the day you get rid of the money pit.

You haven't said if you have a DSM fitted ( sonar unit and tranducer) the C70 is only a multifunction display unit MFDU you then put a card in for navigation, a radar aerial/ scanner or a sonar unit for depth and fish finding . if you have a sonar unit and it's working then press Presentation press Depth Digit and select on / off press OK or cancel to return to the default display hope this helps