Quasar Popular Questions, Answers, Tips & Manuals

https://manualzz.com/doc/47948376/bonaire-vulcan-quasar-manual-wall-furnace-owner-manual

Not sure why anyone would want to repair a non hd TV as the picture quality isn't usable with modern content but if you're doing it because you like restoring something vintage here are some ideas. Some CRT sets use a pulse from the back side of the flyback transformer as a starter voltage supply, it needs this short pulse to start the power supply, it's kind of like starting a gas motor, the starter only runs for a short time then the gas motor takes over, this signal needs to be measured with a scope or a high end meter, this was a common issue with a lot of older CRT sets that use this type of power supply. I'd look at the start up supply as without that the regular supply isn't operatable.

https://issuu.com/balanc3r75/docs/vulcan_quasar_40_service_manual_pdf Se if this is the one you need.

Your EEPROM is bad, if you can find one and have soldering skills and the equipment to remove and replace SMD devices that's the cheap way to fix( $15) if not replace the main board, in your case with the sound issue it may make more sense to replace the main as that should correct that isue as well

You can't., there are too many! Visual ID perhaps. https://www.google.com/search?q=Quasar+remote&rlz=1C1QJDB_enCA643CA644&sxsrf=AOaemvL0VTmVEZKq6ZL80XiQa36s1qdAkQ:1643244756606&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjZ0_vf29D1AhVVj4kEHcJeBwEQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

Your issue is .................................

I gather, from your somewhat garbled post, that you wish advice on charging your equipment. Full instructions will, of course, be in the manual, but as a start I would suggest plugging one end of the lead into the item, the other into an active wall socket.

no model TV told at all.nor year made. 1967 to 2004?????? not sure what you are attempting at all first off there are no more VHF/UHF wide band TV now. its all gone. bye bye. HDTV yes , old analog is gone. buried. this TV is NOT CABLE ready, back in 1967 era,no such thing. make relic TV work needs a video to vhf channel 3/4 converter like old Pong or ATARI games had. yes there are converters. to do video to modulated channel 3/4 but not told at all what is your video choices,?sources. DVD RCA video jacks. cable modems do not have those. I bet you have cable modem or a SAT modem and converting HDTV to analog is wow hard. if not impossible one can record a video sources and convert it using PONG adapter. to old CRT motorola quasar. quasar Company ceased to exist in 2004. ! Beside Uwave ovens. and Motorola 1974 sold its television business to Matsushita Electric, now Panasonic https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313&_nkw=+RF+Modulator+RCA+Input+Channel+3+4+Adapter+Output+&_sacat=0 the above will work ch.3/4 VHF with video sources.

type in quasar VCR model number manual

sorry you'll have to buy a new tv>^< this might cheer you up

you will need both a digital antenna and a converter box. if you can put the antenna on the roof or on a tower. if you had a newer tv all you would have to get is just the antenna

the one stated in the free sq4001 manual or a relic universal remote , rare i bet.

I haven't heard of a radio/tv combo since the demise of vhf tv. A reasonable radio reception could be derived from the vhf tv signal making a usable unit without the bother of an additional aerial. For use with uhf tv the radio would probably need an additional aerial for decent fm radio reception - unless the radio is am only... You don't say how old your combo is or give any details. I think the screw terminals could be intended to be connected to a 300 ohm balanced dipole aerial for radio reception only or to mount a loop aerial for indoor tv reception only, if the tv is intended for uhf analogue reception. If the tv isn't equipped with a standard socket for the usual 75 ohm coaxial type aerial lead it is possible the set manufacturer originally supplied an adaptor to fit to those two screws in order to provide a regular aerial socket. Without a much more detailed description, these are the only comments I am able to make.

Does it have video input available?

Check the edge of the tape to see if it's wrinkled. That is the most common problem that shows that line. You may be looking at the head switching pulse too. Since your VCR has no tracking adjustment, it has to be done with special tools, an oscilloscope and a voltmeter. Not an easy task.

You didn't say the brand or model so its kind of hard to help...try doing a factory reset, again if I knew more I could tell you how to do it if your not sure

Here is a link to the user's manual. Hope this helps! Good luck and have fun on your vacation! :) https://www.manualslib.com/manual/303358/Quasar-Palmcorder-Vm-D52.html Quasar Palmcorder VM D52 User Manual

I suggest you pull it apart and check the many drive belts, they may be defective and loose. If they are replace them all of them.

Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.