Electrolux Dishwashers - Recent Questions, Troubleshooting & Support

See page 28 Solution to Common Problems in user manual for help User manual Electrolux ELFW4222AW (English - 32 pages)

Hi I think I’ve got the same problem that the overflow plastic tray didn’t move down due to dirt. See pic. Anybody an idea how to open/ remove and clean this tray on Electrolux dishwasher?

The pressure switch in a dishwasher, like the Electrolux ESL6201LO, is a component that helps regulate water levels and prevent overfilling. It's an important part of the dishwasher's water management system. However, I must clarify that specific part numbers, designs, and configurations can vary by model and production date. If you're looking for parts or information about the pressure switch for your dishwasher, I recommend the following steps: 1. **Consult the User Manual:** Check the user manual or documentation that came with your Electrolux dishwasher. The manual might provide information about parts, part numbers, and troubleshooting for your specific model. 2. **Electrolux Customer Support:** Reach out to Electrolux's customer support or service center. They can provide you with accurate information about the pressure switch and help you find the correct replacement part if needed. 3. **Online Appliance Parts Retailers:** Websites that specialize in appliance parts, such as RepairClinic, AppliancePartsPros, and eReplacementParts, often provide diagrams, parts lists, and compatible replacement parts for various appliances, including dishwashers. Search using your model number to find the pressure switch or related parts. 4. **Local Appliance Repair Shops:** Local appliance repair shops often have access to a variety of appliance parts, including pressure switches. They might also be able to assist you in identifying the correct part. 5. **Electrolux Authorized Service Centers:** Contact authorized service centers for Electrolux appliances. They should have access to genuine replacement parts and can provide professional assistance. When searching for parts, always make sure you have the correct model number and, if possible, the part number of the specific component you need. This information will help ensure that you get the right part for your dishwasher model.

buy the manual or get it fixed? moved you out of cars

Error code C13 on an Electrolux dishwasher model EHT8ILG8 indicates a problem with the water supply to the dishwasher. The code specifically refers to a problem with the water pressure, which could be caused by a clogged water inlet filter, a malfunctioning water inlet valve, or a problem with the water supply hose. To troubleshoot this issue, first check the water supply hose to ensure that it is not kinked or clogged. Then, clean the water inlet filter and make sure that the water supply to the dishwasher is not restricted in any way. If the problem persists, it may be necessary to call a professional technician to diagnose and repair the dishwasher. Please keep in mind that this is based on general information, the error code meaning may vary depending on the model and brand. It's recommended to check the dishwasher manual or contact the manufacturer's customer service for more specific information.

My six year old Electolux Dishlex DX 403 dishwasher stopped heating the water. I found comments on the internet about burnt out solder joints in the control box. A friend opened the control box and found a blackened area on the back of the circuit board. Once the connection was re-soldered the water heated again. We also found that quite a few wires leading to the control box had overheated and the insulation had melted. Considering that this dishwasher was the top model from Electrolux at the time, I was not impressed. I had previously had a Vulcan Dishlex for almost 20 years.
Thanks to those people who previously posted information about this fault.

i think that is engaged via a _(i can't think of the word.. it's a points set that works off an electro-magnet) if that got stuck then it will keep the pump engaged in the drain mode.. otherwise it's an issue with the settings.

Question edited for clarity and full 'make model (what it is)'. Question moved from Cars and Trucks category. It is a commercial unit and should be repaired professionally. Help in the link https://www.google.com/search?q=electrolux+wt55+overheating+solution ..

fault is probably heating element but you need a megga to test it. other disconnect element, tape up wires then check on wash cycle. be carefull!!

It could be anything. They have a diagnostic brain that creates beeps or codes, but never hear of one that beeps 120 times. You can try power cycling it. Remove mains power for 2 minutes and try again. If that doesn't fix it you will need a service call. If it is the control board, you may consider a new machine is a better option.

Thank you This worked for me!

The heater was ok found dry joint on pc board

see attatched photo

Took top 6 screws out of door holding front panel in place
Removed front switch panel
I then labeled the 6 cables with 6 being for the heater
Removed pc board from housing to find dry joint
using small piece of wire and solder repaired board
re assembled
now as good as new

Hi, Please pour soap and/or toothpaste at the bottom of the washer. This should unclog any drains that the dishwasher uses. And you can also remove any debris present at the bottom of the dishwasher as well. Otherwise, you need to schedule a home depot repair appointment please. Thank you.

I would replace the switch assembly.

Yes, the water inlet valve is leaking and letting water in past a faulty seal. The valve just needs replacing with a new one. They are not serviceable. https://www.google.com/search?q=AEG%2C+Electrolux+%2C+Favourit+parts%2C+water+inlet+valve ..

Not sure if this is same as my (older) dishwasher, but mine has a float switch ( a piece of styrofoam which triggers a microswitch) which sits in the bottom pan. As soon as any water accumulates here, the pump keeps running. I then get error code 30.

Hi
soyunds like it flooded the base
You need to dry out the base of the machine thoroughly and it should re set

No Service Manual online Parts schematic are normally on the images tab, but not even those for 'W' or 'X'. https://www.google.com/search?q=electrolux+esf5201low+parts+diagram

https://medium.com/@MarkRobertshaw/how-to-reset-the-anti-flood-device-on-your-electrolux-dishwasher-76f8997d6dcd https://www.partselect.com/Dishwasher+test-float-switch+repair.htm

Run a long, hot, bleach wash. A couple of cups of Javex should do it. https://www.google.com/search?q=clean+the+trap+in+Electrolux+Dishwasher+GLD2440REC1 ..