Home - Page 5 - Popular Questions, Answers, Tips & Manuals
Need a manual for a Seiko melody in motion wall click. Model # QXM123BRH
Here is a manual for the Seiko Melody in Motion Wall Clock, Model # QXM123BRH:
Getting Started
- Insert one "AA" size alkaline battery into the clock's battery compartment.
- Set the clock to the correct time by pulling out the time-setting knob and turning it clockwise or counterclockwise to set the time.
- Push the knob back in to the "Lock" position to finish setting the time.
Melody Selection
- Press the "Demo" button on the clock's front panel to listen to all the available melodies.
- To select a specific melody, press the "Melody" button repeatedly until the desired melody plays.
Volume Control
- To adjust the volume of the melody, press the "Volume" button repeatedly until the desired volume level is reached.
Light Sensor
- The clock is equipped with a light sensor that will automatically turn off the sound and motion sensors when the room is dark.
- To disable the light sensor, push and hold the "Light Sensor" button for approximately 5 seconds until the "OFF" indicator appears on the display.
- To enable the light sensor, push and hold the "Light Sensor" button again for approximately 5 seconds until the "ON" indicator appears on the display.
Motion Sensor
- The clock is equipped with a motion sensor that will detect movement in front of the clock and activate the sound and motion sensors.
- To disable the motion sensor, push and hold the "Motion Sensor" button for approximately 5 seconds until the "OFF" indicator appears on the display.
- To enable the motion sensor, push and hold the "Motion Sensor" button again for approximately 5 seconds until the "ON" indicator appears on the display.
Nighttime Silencer
- The clock is equipped with a nighttime silencer that will automatically turn off the sound and motion sensors during a designated period of time.
- To set the nighttime silencer, push and hold the "Nighttime Silencer" button for approximately 5 seconds until the "SET" indicator appears on the display.
- Press the "Melody" button to select the start time for the nighttime silencer.
- Press the "Volume" button to select the end time for the nighttime silencer.
- Push the "Nighttime Silencer" button again to save the settings and exit the nighttime silencer mode.
Troubleshooting
- If the clock does not operate properly, try replacing the battery with a new one.
- If the clock still does not operate properly, contact Seiko Customer Service for assistance.
Note: This manual is for general information purposes only and may not cover all features and functions of the Seiko Melody in Motion Wall Clock, Model # QXM123BRH. Please refer to the manufacturer's instructions for complete information on how to operate and maintain your clock.
3/3/2023 4:07:26 PM •
Home
•
365 views • 0 helpful votes
Projection Clock. The time projection turns off after a few minutes.
It is difficult to answer without FULL 'make model (what it is)'. These projection clocks work in the same principle, but in two ways. The time is on a LCD film and light is shone through it, then through a lens and projected onto the ceiling. The projection light can be done in two ways;
- A white LED illumination light and a red LED light that comes on via an electronic timer, say 5 minutes white and then red constant
- or a single LED what is white or red depending on the voltage supplied to this variable voltage LED.
The only way to fix it would be to send it for repair as it is an electronic fault You could however check the manual in case there is a setting to turn off the Red LED. I had a CD Alarm Clock Radio and the projector was the first thing to fail followed by the rest of it 3 years later. I wasn't that worried as I won it in a charity raffle. My GE Alarm Clock Radio is still going strong 48 years later!
Google
make model manual
..
4/2/2023 6:08:59 PM •
Home
•
102 views • 0 helpful votes
Fiberglass Resin curing time?
READ THE INSTRUCTIONS THE AMOUNT OF 2ND PART CATALYST SETS THAT. (AKA HARDENER)
2 DAYS IF LUCKY.
YOU DID NOT USE ENOUGH HARDENER,
4/13/2023 4:20:56 PM •
Home
•
72 views • 0 helpful votes
I have a Bulova B1987 mantel clock. I bought it in December 2022. It is now March 2023 and it has stopped chiming. It keeps perfect time, just won't chime.
There are a few potential reasons why your Bulova B1987 mantel clock has stopped chiming:
- Check if the chime switch is in the "on" position. If it is not, switch it to "on".
- Make sure that the clock is wound fully. A clock that is not fully wound will not chime.
- Check if the chime melody selector is in the "off" position. If it is, move it to a melody position.
- If the clock has been moved or bumped recently, the chime hammers may have been knocked out of alignment. This can be fixed by a professional clock repair person.
- The chime rods or hammers may be damaged or worn out. This can also be fixed by a professional clock repair person.
If none of these solutions work, it may be best to contact a professional clock repair person for assistance in fixing the clock's chime.
3/3/2023 8:12:23 PM •
Home
•
100 views • 1 helpful votes
Not finding what you are looking for?