Lost password need to reset to default - Honeywell HRDP16D500 16Channel DVR 500GB HDD Internal DVDRW (2) USB Ports 120 IPS NTSC

what is Mobile Phone model?You need to reset the old phone password and set new password..To reset the password lock..you can use default code..Try 1234 or 0000 these are default codes...If these code does not works get the master reset code as free of cost from the site Unlocking4free.com/nokia-unlock-tool and reset the Nokia DCT phones from password lock...Then set a new password or security code.

The best thing that you can do ,since you forgot your password is to reset the router .After resetting the router (netgear router)the password will be back to default username and password.
The default user name is "admin" The default password is "password"
All you need to do is to press the reset button for more than 10 seconds with the power on.
Thank you and have a great day

Hello,
You have several options. However, I'm unsure if you have lost the username/password to access your D-Link router's setup/configuration page or if you have lost your wireless access code (used to access your wireless internet).

If you have lost your username/password to your routers setup/configuration page first try the factory default combination.

The default username is: admin
The default password leave blank

If you have customized the username and password during the original install you will have to reset the router to its factory default settings. To do this:
PLEASE NOT THAT BY DOING THIS YOUR ROUTER WILL BE RESET TO FACTORY DEFAULT AND WILL HAVE TO BE RECONFIGURED
Locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a
paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process.

Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is: admin and leave the password box empty.

Please let me know if I can assist you further.

Regards,
KYTechnology

You don't need a password to hook up a second computer - just plug it in. You only need the password if you want to change the configuration of the router.If that's the case, the default user ID for this model is 'Admin' and the default password is 'password'. If you have a non-default password you will have to reset the router to factory defaults and then login with the default ID/password.
To reset to factory defaults, press and hold the Reset button until the Test LED turns on (about 10 seconds). Release the Default Reset button and wait for the router to reboot

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

or

if there is a small hole in the front or back of the router push a hair pin in to reset to factory settings

hope this helps

You need to perform a factory reset. the reset button is on the back next the the antenna. press and hold for 10 seconds - the router will then restart. This will reset the password to the default.
the default password is password.

Forgot your Windows password? A Windows Password Reset Disk could do all the job for you, it can reset your lost or unknown Windows password safely and quickly without login, you can create a Windows password reset disk with the tool Windows Password Breaker, then use it to reset your password.

Do a hard reset. On most typical routers you hold down the tiny reset button with a paperclip for a few seconds until all the lights shut off, and quickly release it (5-15 seconds depending on model usually).
Then it will be reset to factory defaults, and you must go set up everything again. By default the password is usually (not always) 'admin'

There should be a recessed button on the back of the router that you need a paper clip or something similar to access. Press that button down for about 20 seconds and it will reset the router to default settings. Then use the default login/pw to reconfigure it. There is no way to recover a lost password from a router. If you know the exact model of the router, you can download the user manual from dlink's website.

If you forgot the password of your router, you can reset it by pressing the reset button of the router for 20 seconds while the power is ON and after that power the router off for 5 seconds and then the router will be back already to its default settings with default password...