How do you turn off the alarm function on a us polo 1870 watch

If your Timex Expedition watch alarm and beep function are not working properly, even with a new battery, it could be caused by a few different things. Here are some steps you can try to troubleshoot the issue:

1. Check the alarm settings: Make sure the alarm is turned on and set to the correct time. Also, check that the alarm is set to the correct mode, such as daily or weekly.
2. Check the watch's manual: Refer to the instruction manual that came with your watch to see if there are any specific instructions for setting the alarm or beep function.
3. Check the vibration function: If the vibration function of the watch is not working, it could cause the alarm and beep to not function properly. Try resetting the watch or contacting Timex for assistance.
4. Check for physical damage: Inspect the watch for any physical damage such as a cracked or broken case, or a damaged alarm switch.
5. Check for water damage: If the watch has been exposed to water, it could cause damage to the electronic components. If water has entered the watch, it is best to take it to a professional watch repair center for service.
6. Check if the watch have a warranty: If the watch is still under warranty, you should contact the manufacturer for service or repair.

https://disqus.com/home/discussion/channel-exweltiohe/us_polo_assn_watch_owners_manual/

Hopefully, this will help...

Lego Watches Manual Instruction:
There are 4 buttons on this lego watch case, Light button, Mode button, Stop button and Reset button, now I will show how to set the time easily!
1, Light Button: Press this button, the watch LCD light will display for 3-5 seconds;
2, How to use the stopwatches chronograph function?
Answer: When the lego watches in normal working condition, Press "Stop button" for 1 time, then the watch goes into the chronograph mode, then you can use "Stop button" and "Reset button" to operate this function.
3, How to set the alarm time?
Answer: When the lego watches in normal working condition, Press "Stop button" for 2 times, then the watch goes into the alarm mode, then you can use "Stop button" and "Reset button" to set the alarm time, also you can turn off or turn on the alarm function and chime on every hour function by the same operate.
4, How to set the right watch time, hour, minute, second, week, date, month, year?
Answer: When the lego watches in normal working condition, Press "Stop button" for 3 times, then the watch goes into the time setting mode, then you can use "Stop button" and "Reset button" to set the second, minute, hour, week, date, month and year.

This is all. So now please have a try to set your lego watches time!

http://www.freestyleusa.com/support/

the second window down has the buzz instructions.

in the buzz instructions

TO TURN ON/OFF THE ALARM AND
HOURLY CHIME:
1. Press S3 button to select HOME ALARM or FOREIGN ALARM to set. 2. Press S1 button to activate the alarm. Alarm indicator /
will appear.
3. Press again to activate the hourly
chime. Chime indicator will
appear.
4. Press the third time to activate both
functions. Both of the indicators
will appear.
5. Press fourth time to deactivate both
functions. Both indicators will
disappear

Thank you, coffee_addct!!!!

Can you email me the instruction manual
[email protected]
Thank you
Renee

Use the mode button to toggle to the alarm function. Once at the alarm function, press start/stop. It wil turn the alarm on or off as well as the hourly chime.

mcdevito75 here, By pressing the MODE button until you get to the alarm function and turn it to on or, set an alarm time for the alarm to go off.

I just have to say, we bought the same watch in 2014, at a Meijer store. The directions were totally incomprehensible, and this watch has spent every day since in a drawer where the alarm goes off at the same time each day because 4 intelligent adults can't figure out how to change the settings. Ridiculous.

the mode button controls the different functions of the watch.  time, alarm time, stopwatch, timeset, alarmset, in a repeating cycle.  Make sure you are on the time function (seconds ticking and changing every second, but not flashing twice per second.  This is the normal mode that shows the time.
 A press of the lap/reset button (labeled) will show the alarm time, Unpress will show the time of day. Press again toshow the alarm time. Press and hold the lap/reset button will show the alarm time again, but it will hold there.  While holding this lap/reset button, press the start/stop button (labeled). This will turn on (or off) the alarm (tiny indicator).  Press this start/stop button repeatedly (while still holding the lap/reset button and you will see the indicator turning on and off with each press.  Stop this button pressing with the indicator OFF, let up on the lap/reset button, and the time will return to the screen.  The alarm will now be OFF.