Question about General Electric WCVH6800J Front Load Washer

1 Answer

GE Front Load washer keeps pausing and have to keep pressing start,then it will stop at 1 min. left and won't finish.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 44 Answers

Try to clean the discharge pump filter first (Instructions in the Use/Care manual).

If the drain pump is working, it's most likely related to the pressure switch. Check out these postings:

http://www.fixya.com/support/t9807344-ge_front_load_washer_stops_45_min_35_min
http://www.fixya.com/support/t8933273-general_electirc_washer_model


Do a diagnostic test -- Easy and free, and the machine will likely diagnose its own problem. Instructions in those postings.

Posted on Jul 28, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE WCVH6800 Pressing start results in two short beeps. The pause/start button keeps blinking and it will not start a cycle.


Is the door lock button on, but the door not actually locked? Our door lock switch keeps going out. We have replaced it 4 times in the last 3 years.

Jan 16, 2011 | GE WSXH208A Front Load Washer

1 Answer

My front load washer goes into pause two min after machine is started i have to press start for cycle to continue and sometimes it does it a second time press start again it will then finish cycle


you should check button start / pause the washing machine, if it is damaged you must replace it with a new one, the damage caused by the push button which is not connected properly.

Aug 11, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Ge front load washer won't go into rinse cycle.


Check the cold water hose. My brand new machine had this behavior until I discovered a kink in the cold water hose - works great now.

Jun 03, 2009 | GE WSXH208A Front Load Washer

1 Answer

My washer had 1 minute left before the spin cycle was complete.


Push and hold the START button for three seconds if you want it to finish off that last minute.

...or...

Push and hold the PAUSE button for three seconds to stop the cycle.

Peace.

Marco

Jan 31, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Washing machine stops when there is 19 minutes left!


you need to have a tech out to look at it it sounds like the motor isnt going into high spin and /or cutting out on over load this is a problem with the g/e's there is no filter on this machine all the lint is flushed down the drain

Jan 08, 2009 | GE WBSE2090A Top Load Washer

1 Answer

One minute left


be sure water is draining out before spin starts if necessary remove bottom panel and clean pump out and ck hoses to pump be sure there are no excess suds ..wash only full loads small loads or loads with 1 heavy item will cause washer to sense off balance and try to balance load this will extend cycle time

Nov 09, 2008 | Whirlpool GHW9400 Front Load Washer

2 Answers

GE Adora front load washer overloaded now won't start


Washers - Resetting Electronic Controls on a Washer

If there is a pause in the washer cycle, the controls will lock up. The pause can occur because of a power failure or it was put in the test mode at the factory.

Also, if the washer was stopped before the cycle was complete or the consumer has pushed the stop/pause button to temporarily stop the cycle and the cycle is not reset. Over a period of 24 hours, the washer will pump out and spin, but will stay in the final spin.

To correct the situation, shut off the circuit breaker for 30 seconds or unplug the washer, then turn the timer knob around and back to any position other than final spin. Verify the water is turned on and restore power. This should resolve the issue.

Apr 23, 2008 | GE WSXH208A Front Load Washer

Not finding what you are looking for?
General Electric WCVH6800J Front Load Washer Logo

4,045 people viewed this question

Ask a Question

Usually answered in minutes!

Top General Washing Machines Experts

Kevin
Kevin

Level 2 Expert

79 Answers

geapptech

Level 2 Expert

157 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a General Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...