My lid switch fell out of my Whirlpool Top Loader Washer..can I just bind the two wires leading into it to bypass

Kenmore Whirlpool top load washer. lid lock issues - YouTube

? 3:34
https://www.youtube.com/watch?v=Vf1hVhpC8yE
Mar 12, 2013 - Uploaded by EurekaRecycler
Kenmore Whirlpool top load washer. lid lock issues ... The new one I bought or actually have a loan on the EXACT issue and I've only had it 3 ... cheap way to bypass the lid lock which is irritating, aggravating, frustrating on my ...

Kenmore Lid Safety Switch ( Temporarily Fix ) - YouTube

? 13:17
https://www.youtube.com/watch?v=UMlLqEF8EGM
May 20, 2012 - Uploaded by matttherepairman
This is a easy way to bypass a lid safety switch with-out cutting into the wire! Did your Kenmore Washer machine fill up and stop ? Your Lid ... +Jerry Munroe That is correct,,, You will not need to cut any wires Thank you for watching .... Kenmore Whirlpool top load washer. lid lock issues - Duration: 3:34. by ...

how can I disable the lock on my new top load Kenmore ...

www.shopyourway.com > Manage My Life > Questions

Locate the switch by the lid and simply connect a wire between the two wires going to it to affect a bypass.

ITS A SAFETY PRECAUTION SO SHOULD NOT BE BYPASSED BUT SEE PICS ON HOW TO BYPASS

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=110.20712990&pathTaken=partSearch

and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

Following is a description of how to release the console for access to the pins.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf

It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

under the top cover but mounted to top cover find your two leads and trace back to control panel and jumper the leads to bypass switch and this will tell you either switch is good or bad!

Sounds like door switch may be failing, or the wiring between door switch and timer has loose connection. You can replace the switch or check ther wiring, or bypass the door switch circuit by jumping the leads at the timer