How to connecting Aztech modem DSL600E with Router linksys WRT54G

First!
Do you have a connection in your modem?
if you do, you need to set up the linksys router in DHCP internet set up.
To have access to the linksys you need to go to:
http://192.168.1.1
The password it's admin
and the username in blank (no password)
change the internet setup to DHCP

Make sure you don't have the Same address for 192.168.1.1 or you modem cause if you do you'll need to change the ip address on the linksys router...
:)

What kind of internet service are you hooked up to?

Are your setting to your ISP setup correctly?

Is the firmware for your router updated?

Not that you need to all teh time but, did you install the router software?

Check those out and let me know.

Hope that helped
Corey

www.appliancesplus.net

It appears the connection between the Linksys and the modem is not working.
Try a different LAN cable.
Check the LAN cable from the modem to the Linksys, it should be connected to the WAN/Internet port on the Linksys.

Darvin, gotta love your ISP. Never fear......

if it isn't too much of a problem (knowing you have wireless setup done already), then do a factory reset on your router ** remember to copy the WEP Key if you have, or recall the PASS PHRASE so you won't have to reset all wireless devices ** Reset is located on back, you need a ball point pen to reach the reset switch.

Reset process: unplug, take ballpoint pen & insert into reset switch & plug unit back in. Sometimes tricky, but you should notice green light goes to yellow/orange upon resetting.

RESET or NOT - you want the Linksys set for ::

Connection Type - AUTOMATIC (for automatic discovery)
Router IP Address - 192.168.2.1

DCHP - ON, Addresses - 192.168.2.100 and allow 5-50 users
(for security, assign the number of DESKTOP + WIRELESS expected users +1, this way you don't get overrun without knowlege)

Take the cable from Aztech ETHERNET OUT to WAN on Linksys. (usually BLUE) (??) not 100% sure as I have the little silver pocket edition of the same Router. - power cycle (turn both DSL modem & Linksys off for 20 seconds. turn on DSL Modem, wait till it's about as ready as possible, turn on Linksys, should only take 20-30 seconds to power up & recognize.

VERIFY SETTINGS: access router - 192.168.2.1, goto STATUS. you should see IP Addressing, SubNet, DNS1 & DNS2 settings. If you do not, then you have no internet connection.

ALTERNATIVE,

Setup Linksys Router with COnnection Type: PPoE, you will need your ISP assigned ID & Password. Follow all other instructions properly.

If you still have problems, please contact me at 906-495-1707 or via Yahoo IM [email protected] or through this website.
once

hey there, can u acces the gateway of the router

192.168.1.1 than enter ur login & password

than reset the router to fabric setting when done go back in the router and configure it as u like to have it

the links below will show you how to manually install the device on your network

Setting up your Linksys router for Cable ISP


Setting up your Linksys router for DSL ISP


Setting up your Linksys router to have wireless security.


if you have other questions just let me know.

Hi i have found some useful information ...
PLease click on the link;

http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4963&p_created=1168254340&p_sid=Dr5KyRBj&p_accessibility=0&p_redirect=&p_lva=3687&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MjgsMjgmcF9wcm9kcz0wJnBfY2F0cz0xNzIxLDE3MjMmcF9wdj0mcF9jdj0yLjE3MjMmcF9zY2ZfMz0xJnBfcGFnZT0xJnBfc2VhcmNoX3RleHQ9Y2FzY2FkaW5n&p_li=&p_topview=1

Or thry this second option

http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4579&p_created=1165892402&p_sid=Dr5KyRBj&p_accessibility=0&p_redirect=&p_lva=3687&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MjgsMjgmcF9wcm9kcz0wJnBfY2F0cz0xNzIxLDE3MjMmcF9wdj0mcF9jdj0yLjE3MjMmcF9zY2ZfMz0xJnBfcGFnZT0xJnBfc2VhcmNoX3RleHQ9Y2FzY2FkaW5n&p_li=&p_topview=1

your starband is if im right the cable modem ? connect the modem to the router and then the router to the computer ? then run the linksys easy connect @ www.linksys.com/support

To setup your router
first check..
Connect the Broadband modem to the computer using an Ethernet cable without the router installed and make sure that the Internet connection is active. If it is not, contact your Internet Service Provider. If it can go online,
to setup connection..
Step 1:
Connect the Broadband modem to the router’s WAN or Internet port.
Step 2:
Connect the computer to any available numbered port (1, 2, 3 or 4).
NOTE: In this example, we’ll connect the computer to port number 3.
Step 3:
Make sure the power adapter is plugged to an available power outlet.
Step 4:
check if you are able to go online wired..
if not your router has to be configured first,
to config your router i need some more information
your internet service providers (isp)name , and how many computers do u have totally..

To setup your router
first check..
Connect the Broadband modem to the computer using an Ethernet cable without the router installed and make sure that the Internet connection is active. If it is not, contact your Internet Service Provider. If it can go online,
to setup connection..
Step 1:
Connect the Broadband modem to the router’s WAN or Internet port.
Step 2:
Connect the computer to any available numbered port (1, 2, 3 or 4).
NOTE: In this example, we’ll connect the computer to port number 3.
Step 3:
Make sure the power adapter is plugged to an available power outlet.
Step 4:
check if you are able to go online wired..
if not your router has to be configured first,
to config your router i need some more information
your internet service providers (isp)name , and how many computers do u have totally..