Wrong current location

The "New Location" fix above brought my GPS 60 back to full HELP NUMBER +1 833 272 0777operation. I did reload the GPS software from Garmin but the recovery depended on well charged batteries and as above: turn the unit on
press MENU button
scroll to "New Location"
wait 10 minutes for the GPS to recover

Ca - Average Current peak - happens if there is a 2 second average of current draw greater than 5.55 amps at the motor windings. This may signify problems with the drive motor, thermal protector, or motor controller. Overloading the unit may cause this problem. Try washing smaller loads and see if the problem goes away. If it recurs when you wash bigger loads, decrease the size AND watch to see if you have to continue to decrease the size to keep the error from happening. If that were occurring, it could well be a sign of the electrical problems noted, requiring service.
CA Cl Average current limit Or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either CA for average current limit trip or Cl for instantaneous current limit trip. Average current trip occurs if there is a 2 second average of current draw greater than 5.55 amps at the motor windings. Instantaneous current trip occurs if there is a spike of 26 amps instantly at the motor windings. This may signify problems with the drive motor, thermal protector, or motor controller. Over-loading the unit may cause this problem.
I think CA means [C]ontrol [A]verage Error. It means you need to reset the control panel, and retry again.

Hello joe_east,

The Belkin Router's software (firmware) can be occasionally updated. To check for new updates, go to the Belkin Router Setup page http://192.168.2.1/ . The following choices will appear to update firmware and save current settings:

•Select Firmware Update (Near the bottom of the left-hand panel)
From time to time, Belkin may release new versions of the Router's firmware. Firmware updates contain improvements and fixes to problems that may have existed. Click the link below to see if there is a new firmware update available for this Router.
•Firmware update Options:
Firmware Version > #.##.##
Check for New Firmware Version > [Check Firmware]
Update Firmware > [Enter file name/Browse]
[Update]

•NOTE: Please backup your current settings before updating to a new version of firmware. Click Here -> http://192.168.2.1/system_c.stm to go to the Save/Backup current settings page.
•Save/Backup Settings
You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you backup your current configuration before performing a firmware update.
*Saved File name is user.conf*

If this solution is helpful please click a thumbs-up rating below.

Have a great day,
martyshaw152

how are u am scott hope i can help ok i have the same washer this CA code means AVERAGE CURRENT LIMIT, OR INSTANTANEOUS CURRENT LIMIT. if a status comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either "CA" for average current limit trip, or "CI" for instantaneous current limit trip. AVERAGE CURRENT TRIP occurs if there is a 2-second average of current draw greater than 5.55 amps at the motor windings. INSTANTANEOUS CURRENT TRIP occurs if there is a spike of 26 amps instantly at the motor windings. This may signify problems with the drive motor, thermal protector, or motor controller. or overloading the unit may cause this problem. press stop/cancel to clear the display good luck

As far as the car charger, I located one on eBay from a trusted seller for about $8 (includes shipping charge). Click here: http://bit.ly/dbdebr

To update your c55o, click on one of these links:
StreetPilot® c550 Part Number: 010-00522-00

Support

1. Update Unit Software with WebUpdater
• Use WebUpdater to automatically keep your operating software current.
Unit Software
• StreetPilot c550 Ver. 6.70 as of Dec 07, 2008 | Download

==========================================
If you found this information helpful, please give me a big thumbs-up when you rate my answer. Thanks!

Hello there:
the ca or even a ci can mean the following
CA
Cl Average current limit Or
Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either CA for average current limit trip or Cl for instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current draw greater than 5.55 amps at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or motor controller. Over-loading the unit may cause this problem.

Press STOP/CANCEL to clear the display
unplug the machine for 1 hour and then plug back in and see if the error is now cleared

Under Settings go to settings then general

1. Under International set the Region Format to "United States"
2. Under Time Zone set thid to where ever you are e.g. Miami, USA
3. Then under Location Services switch this on

Then go to maps and when prompted let it allow you to use your current location

http://www.applianceaid.com/calypso-codes.html#wash

CA Cl Average current limit Or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either CA for average current limit trip or Cl for instantaneous current limit trip.
Average current trip occurs if there is a 2 second average of current draw greater than 5.55 amps at the motor windings. Instantaneous current trip occurs if there is a spike of 26 amps instantly at the motor windings. This may signify problems with the drive motor, thermal protector, or motor controller. Over-loading the unit may cause this problem.

Hi,
The C1 code signifies "Average current limit Or Instantaneous current limit."

If a status signal comes back from the motor controller that a current
limit has been breached, the unit will return to standby mode and
display either CA for average current limit trip or C1 for
instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current
draw greater than 5.55 amps at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps
instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or
motor controller. Over-loading the unit may cause this problem. "

Please check down the drive motor to resolve the issue.
Have a blessed day!
Thanks!
mannu_rakesh

It sounds like you need to do a master reset. Here's how..

To reset the unit you will need to press the bottom right hand corner of your screen and hold in (relatively firmly) and then press and hold POWER, make sure you release the power button when the unit turns on and a message will appear asking if you wish to clear all user data - select YES to this.

This will completely wipe all data on your unit including almanac data (satellite information). Your unit would then need at least 45 minutes with clear view of the sky to update the almanac and re-acquire a GPS fix which will show your current position.

This should fix the problem because it will be the way it was out of the box. When you turn it back on it will scan for it's exact location.

Good luck! I hope you have purchased a new unit, I can't imagine living without one now :-)