I do not know what the 6 buttons on top are for???? Model ONB17AA001

1. To enter the Service Alignment Mode (SAM), press the following key sequence on the remote control transmitter: 0-6-2-5-9-6-Status.

2. From the top level SAM menu, use the Menu Up/Down keys to highlight the Geometry sub menu.

3. Use the Menu Left/Right keys to enter the Geometry sub menu.
4. In the Geometry sub-menu, use the Menu Up/Down buttons to select VAM.
5. Using the Menu Left/Right keys, adjust VSH so that the horizontal bar is properly centered, top to bottom.

6. Using the cursor up/down keys, select VAM from the Geometry sub-menu, and use the Menu Right key to

increase the value to obtain a slight overscan.

7. If other Geometry adjustments are needed, proceed to the necessary adjustment using the Menu Up/Down

buttons.
8. Upon completion of Geometry adjustments, press the Menu button to return to the top level SAM menu.
9. To exit the Service Alignment Mode, turn the set off with the Power button on the remote control.
 

Possibly a similar model - free online :

https://fccid.io/G3OONA17AA015/User-Manual/UserMan-3313968

ONA17AA015 CD MINI STEREO SYSTEM User Manual UserMan ACE INTERNATIONAL...

Usually the model number and info is on a sticker on the back of the fridge , you will more than sertainly have to move your fridge to find this info.

On the silver part on top of the grinder is a button , press this button and hold it down. now turn the blade until it stops moving, this locks the blade, keep holding the button down and turn grinder over ,and turn the nut counter clockwise, and remove it , take old blade off ,put on new one .it should go over the shaft and at the bottom on a "fit" Make sure it is on the "fit". replace the nut and tighten. If you dont get the nut tight enough it will loosen while in use and the disc you are cutting/grinding with will wobble and may even come off causing possible injury .

1. Menu(top left button) 2. 8 3. down 2 times 4. select(center button) 5. down once 6. options(top left button) 7. 5 8. 2 9. select(center button) 10.copy(top left button) 11.down 1 time 12.select(center button) 13.down 2 times 14.select(center button) Sorry if the specific buttons are unclear, I tried to make them as simple as possible

sounds like your timer went bad, try and replace the timer that is behind the knobs, you will know what the timer looks like because it is behind the knob that allows you to set whatyou want to run and for how long.

There is a power button on top of the tv. There are 6 buttons on the top of the tv and the power button is the one on the right. They are located about the center of the TV.

Region code hack posted by Tiger1, May 24 2007:

Hi I live in Australia and added this model.



acknowledging: Region code hack posted by ZoidsGodzilla, November 22 2006: for the Samsung DVD-V5600

1. Press the DVD button on your remote (the Samsung logo appears)
2. Press the SUBTITLE button on your remote
3. With your remote enter the code: 76884
4. The current region is displayed on the top left corner of the screen. (e.g. 4)
5. Press 9 on your remote (Region free)
6. Again press the SUBTITLE button on your remote
7. Enjoy the Region free player

If your player is NOT Region 4 by default then you will need to Substitute the Numbers in Step 3 with the ones Below.

Region codes:
RC 1: 2, 9, 3, 3, 4
RC 2: 3, 8, 7, 6, 7 (or 5, 7, 5, 3, 8 )
RC 3: 5, 6, 7, 3, 2
RC 4: 7, 6, 8, 8, 4
RC 5: 5, 3, 8, 1, 4
RC 6: 2, 4, 4, 6, 2

For Example if your Player was Purchased in the usa ( Which is Region 1) then Step 3 would read :-

3. With your remote enter the code: 129334

Have Fun :0)