Replacement Outdoor Temperature Sensor for Atomic Clock

Adding the word 'Skyscan' makes all the difference. All questions need 'make model (what it is)' as the first 3 words please.

https://www.google.com/search?q=Skyscan+87700%2C+replacement+outdoor+temperature+sensor

..

Direct from the maker

https://sharpclocks.com/support/

SPC1107 Manual_OL - Sharp

https://sharpclocks.com > uploads > 2019/01 > SP...
PDF
The remote sensor transmits the outdoor temperature. To receive the outdoor temperature, place the ... M.Z. Berger will repair or replace the clock.

• 
  

  SPC1107A - SharpClocks

  https://sharpclocks.com > products > spc1107a
  The Sharp Atomic Clock will always be accurate to within one second as it receives daily WWVB updates. The Wireless Sensor transmits the outdoor temperature to ...

Remove all batteries from outdoor sensor and weather station.

Press one of the buttons on the weather station at least 20 times to clear all memory.

Verify that the weather station is blank before proceeding (there may be lines painted on
the screen that will show when power is removed).

Leave both units without power for 15 minutes (very important).

Insert fresh batteries into the clock.

Insert fresh batteries into the outdoor sensor.

Press the TX button on the outdoor sensor to transmit RF signal.

Keep the outdoor sensor 5-10 feet from the forecast station.

When RF connection is established, the temperature will appear on the station. Allow the
outdoor sensor and weather station to sit together for 15 minutes to establish a strong
connection.

[PDF]WS-8117 ATOMIC CLOCK WITH OUTDOOR WIRELESS ...

https://www.lacrossetechnology.com/products/.../misc/8117-manual.pdf

NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions

https://www.lacrossetechnology.com/support/top_solutions.php

A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here

www.weather-station-products.co.uk/faqs/common-issues-weather-stations

Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite

www.acurite.com > All products

Hi Susuan,
One of these methods below should get your device working properly. Good luck!
LaCorosse Tech Support email address.
The product information page
From the manual:
915MHz RECEPTION CHECK FOR OUTDOOR TEMPERATURE SENSOR
The atomic clock will receive the temperature data within 3 minutes. If the temperature data is not being received 3 minutes after setting up (the display shows "- - -"), then please check the following points:
1. The distance of the atomic clock or outdoor temperature sensor should be at least 6 feet (2meters) away from any interfering sources such as computer monitors or TV sets.
2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.
3. Using other electrical products such as headphones or speakers operating on the same signal frequency (915MHz) may prevent correct signal transmission and reception.
4. Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference.
Note:
When the 915 MHz signal is received correctly, do not re-open the battery cover of either the outdoor temperature sensor or atomic clock, as the batteries may spring free from the contacts and force a false reset. Should this happen accidentally then reset all units (see Setting up above) otherwise transmission problems may occur.
The maximum transmission range is 330 feet (100 meters) from the outdoor temperature sensor to the atomic clock (in open space). However, this depends on the surrounding environment and interference levels. If no reception is possible despite the observation of these factors, all system units have to be reset (see Setting up).

Double check the batteries to make sure they are installed correctly. If one of the batteries in the outdoor sending unit is in backwards, it will not send the outdoor data. On the indoor unit, there is typically one battery that is used for receiving the signal from the outdoor unit. If all of the batteries are in correctly but that one, you will see the display and the indoor temperature information, but the outdoor information will not be displayed.

After replacing the transmitter batteries several times, I tried replacing the clock batteries. They must have been getting low. Once I put in new batteries in the clock it worked fine. Good Luck.