Question about Ovens

1 Answer

I cant get my oven to stay on model # FFEF3015LSM after a few minutes is turning oven on, it starts to beep and screen says F30

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 181 Answers

It looks like the probe is the same as the temperature sensor.

On some models, you can recalibrate the oven control up to 35 degrees Fahrenheit higher or lower. Refer to your owner's manual for instructions on how to recalibrate the oven control.

Since you're getting an error message the following may apply:

OPEN PROBE CONNECTION
1. (F30 or F31) Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector.

SHORTED PROBE CONNECTION
2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted Sensor Probe harness between EOC & Probe connector. .

from: Frigidaire FEFS52DSD Service Data Sheet

Possible Replacement Part:
http://www.repairclinic.com/PartDetail/Frigidaire-Range-Stove-Oven-Temperature-Sensor/316490000/1197392?modelNumber=FFEF3015LSM&fromRepairHelp=True&ss=a13b2d1284938

Posted on Mar 24, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I have Fridigaire double oven part# PLEB27T8ACA with F8 code prob

wow, that is so weird...i was just getting ready to write the exact same thing. this last time mine beeped, i just kept letting it beep for several minutes. if kept on. i then went in and pressed all the buttons except for cancel and nothing happened. then i pressed the oven light button. the beeping stopped. not sure if it's coincidence or if that was what i was supposed to press. i will keep messing with the buttons and let you know if i figure it out. i will dread if it beeps all night long.

Posted on Feb 14, 2009

jumptrout51
  • 3361 Answers

SOURCE: f0 error code on ge profile oven

Could be a stuck keypad. Try pressing all pads at random several times each to clear it.
If that does not work the ERC(clock) must be replaced.

Posted on May 26, 2009

localwonder
  • 6784 Answers

SOURCE: Jenn air oven problem

HI. this is a Communication error between boards. Check the wiring harness that links the Power relay board to the Main board. if the harness is fouled on any way, replace it asap. if the harness is in good condition, replace the power relay board.

Posted on Jul 27, 2009

jumptrout51
  • 3361 Answers

SOURCE: GE Profile oven beeps and displays FO

Your electronic oven control(clock) is bad and must be replaced.

Posted on Sep 02, 2009

tbirdfan1
  • 3051 Answers

SOURCE: Frigidaire double oven beeping and showing f8 code

Hello there
First i would unplug it for 1 hr to allow the oven internal reset to reset it'self than plug it back in and see what happens but if this doesent help than here is a listing of the code and what it means
F8 Lock motor relay watchdog is ative when it should be off Microprocessor checking the operation of the EDC lock relay after self clean is selected, relay failed. Replace EDC.
Lock switches Check or Replace component













Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flashing PF 32 error code


Hello - This manufacturer does not show to have such an error code for a wall oven. However the error codes F30/F31 indicates that the unit either has an issue with the oven sensor, wiring with the EOC or the probe connections is open or shorted. Contact a professional to move forward accurately.

Nov 10, 2012 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

Kenmore Elite c970-418091 wont work after self clean - Code f30


Here is a how it works post I{ wrote a little while back.:The oven temperature is regulated by a temperature sensor when placed in self clean the sensor is removed from the circuit and full power is applied to both the bake and broil elements causing an the temperature to exceed in some some models up to 1,000 F. I would recommend against using self clean for the simple fact that no oven cavity to this date has been designed to withstand that high of a temperature and therefore excess heat is passed upward resulting in damaged lock mechanisms, control boards, and other electronic components. With all that said you can try to cycle the controls by turning the breaker of the oven off for a few minutes the n turn it back on. It should then read PF which is normal. Press the cancel button and try it to see if it works. If not then you will need to replace the control board in the upper panel

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Apr 26, 2012 | Kenmore Ovens

1 Answer

After baking pizza oven started beeping and hasnt stopped. It says F24 and wont respond to any button commands except for the "oven off" button which just makes it beep faster. What can I do to...


well what i would do is turn off the power to the stove and let it sit for awhile this should reset it. let itset unplug for 30 minutes or so not just a few seconds okay. good luck

Feb 24, 2011 | Ovens

1 Answer

I have a Kenmore model #40121. I tried to use it today and after it was on for about 15 minutes at 425 degrees it started beeping and flashing F3. I turned it off and back on and about a minute later it...


All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 04, 2010 | Kenmore 40192 / 40199 Electric Single Oven

1 Answer

Kenmore Ultra bake self cleaning oven is showing code E0 - F2


My oven will not stay on, when started to preheat it will come on for a few seconds and they it will make a beeping noise and the codes E0 F2 will appear. The codes stay on even if the oven is off.

Jan 04, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

F30 ERROR


F30 error every time I turn the oven on

Jul 21, 2008 | Kenmore 33464 / 33465 / 33469 Gas Single...

3 Answers

IT WON'T STOP BEEPING!


I had that issue with my oven but turned it off at the meter box for 30 mins and it fixed it. It seems to be caused by electricity surges/power outages

Mar 30, 2017 | Ovens

13 Answers

Kenmore Elite slide in range F30 error


I had the same F30 error problem but fixed it. On my professional series Frigidaire, there are 2 resettable red button locations. I discovered that only one is in the rear of the oven. After going to the breaker box and shutting off the power, pull out the stove enough to work, unscrew the rear screws (I didn't unscrew all of them, just enough to work back there). The small red button is on a small black round piece with two purple wires feeding to it. That was not my problem. Mine was the other red button behind the control panel. Pull off all 4 knobs, unscrew by hand the large black rings that are underneath the knobs, pull out the whole panel. Look back and right (below where the right knobs were located) to find the 2nd red small button. Push to reset. Check this one first since it is easier to do.

Dec 27, 2007 | Ovens

1 Answer

Set, Start and Time Beeps


im going to contack a friend of mine at ge technical about issues on this oven after holidays check back

Dec 31, 2006 | GE JKP15 Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...