Whirlpool Cabrio 7.0 Cu. Ft. Super Capacity Plus 7-Cycle Gas Dryer - White Logo

Related Topics:

A
Anonymous Posted on May 11, 2014

What does the f25 error code mean - Whirlpool Cabrio 7.0 Cu. Ft. Super Capacity Plus 7-Cycle Gas Dryer - White

1 Related Answer

Anonymous

  • 1 Answer
  • Posted on Jul 26, 2008

SOURCE: F25 error code

this is scary. I got a brand new whirlpool duet sport I ordered from Costco.com. After 19 days of waiting for delivery it finally arrived and was installed by the whirlpool dlvy people. I read the instructions and started my 1st load within an hour of being installed. It never worked. Ok it work 6 mins and stopped on every cycle I put it on and then I got the error code 25. I called their customer svc number and they could not even tell me via the phone what that meant. I am suppose to have another delivered here HOPEFULLY next week but after seeing others having repeated problems I do not know if I should just say no take it all back.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

What does an upside down F and then an E error code mean for my Kenmore washer?

really need make and MODEL, but..

Kenmore HE2 front-load washer error codes

  • F01. Main control board EEPROM error. Check/ ...
  • F11. Motor control board failure. Check/ ...
  • F20. Not filling. Check/ ...
  • F21. Will not drain. Check/ ...
  • F22. Door lock failure. Check/ ...
  • F23. Heating element failure. Check/ ...
  • F24. Water temperature sensor error. Check/ ...
  • F25. Drive motor tachometer error. Check/
More items...

Kenmore HE2 front-load washer error codes ' Sears PartsDirect

0helpful
2answers

I have the whirlpool cabrio wed6200sw1 dryer and when i set the drying time to 45 minutes drying time,the timer count's down in about 20 minutes and ends the cycle, got a F25 code when I ran diag's

f25 is a bad thermisiter,find the tech sheet in the dryer and it will tell you how to read out the thermisiter,if the thermisiter is good then you have a bad computer board.
0helpful
1answer

Code F25 on my whirlpool washer

F25 is a MOTOR CONTROL error . check for past posts in Search as there were some in 2007 shown on Fixya . or check throgh Google / Internet explorer by stating F25 Washing Machine error
0helpful
1answer

What the F25 code

Please, head over to this link, it explains by a regular user on what F25 means and it have pictures.

http://neighboursappliance.com/f25-on-a-duet-washer/
0helpful
1answer

F25 error code

The "F25" error code means the control board senses the inlet thermistor shorted. The inlet thermistor is a part of the hi-limit thermostat which is located on the heating element box.

- The hi-limit thermostat kit Part number: AP3094323

Read more: http://forum.appliancepartspros.com/dryer-repair/54078-whirpool-duet-dryer-error-code-f25.html#ixzz2n2Rmgm7a
http://forum.appliancepartspros.com
0helpful
2answers

Front loader maytag stop in middle cycle give error F25

Remove your service panel and look for your tech sheet inside a jacket in the inside of the service panel. An F-25 is usually a broken wire between the main control and the motor control.
themobilian_3041.jpg

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

2helpful
2answers

Fault code F25

Hi,

If you remove three screws along the bottom front the bottom panel comes off.
On the inside, on the right wall, is a plastic bag with a paper labeled "FOR SERVICE TECHNICIAN ONLY".
This has a section titled "FAILURE/ERROR DISPLAY CODES" with all the error codes along with an explanation and recommended procedure. For F25, this is:

DRIVE MOTOR TACHOMETER ERROR

If the control is unable to properly detect motor speed, the machine shuts down.
If a failure occurs during high-speed spin, the door unlocks after 3 Minutes.

Possible Causes/Procedure

1. Verify the shipping system including shipping bolts, spacers and the power cord are removed.
2. Unplug washer or disconnect power.
3. Check drive motor tachometer resistance. It should be approx. 115 ohms.
4. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
5. Plug in washer or reconnect power.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.

I got this working for many on this site :)
Thanks
Fame !
Not finding what you are looking for?

548 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Virgil Watts

Level 2 Expert

267 Answers

Brad Brown

Level 3 Expert

19187 Answers

Paul Bade

Level 3 Expert

1818 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...