Kenmore Elite H3 control buttons - some work some don't

Diagnostic mode for Kenmore Elite He3t model 110 42926 ...

iFixit https://www.ifixit.com > Answers > View > Diagnostic...
Apr 8, 2016 - With the washer empty, close the door. · Push "control/on" or "Start" · Select "Drain/Spin" · Select "No Spin" by pressing SPIN SPEED touchpad.
3 answers · 2 votes: I believe this is very similar to the model I have. Here is what I did to run a diagnostic. ...
F11 error code during Diagnostic test? - Kenmore ...
1 answer
Jan 18, 2016
SOLVED: F11 code error on Kenmore HE3 - iFixit
16 answers
Mar 3, 2011
SOLVED: f h error code - Kenmore Elite HE3 ...
9 answers
Feb 21, 2012
It seems like the washer has no power - Kenmore Elite ...
6 answers
Nov 2, 2017
More results from www.ifixit.com

Diagnostic Test; Starting The Test Mode; Test Program ...

ManualsLib https://www.manualslib.com > ... > User manual
Close the door. Select the DRAIN/SPIN cycle. Select NO SPIN by pressing the SPIN SELECT button five (5) times. Push Prewash Option button four (4)times within ...

..

if its a Kenmore model then this message says that the button control board has lost sight of the main control board , but its been my experience that this maybe able to be reset and it may never come back or it will not reset and the control board will need replaced (50/50)


cycling power may reset this

The F5 error code indicates a water temperature problem. The control board circuit is not recognizing a resistance change in the water temperature sensor.

You most likely have a loose connection at the tub sensor , or a bad heater.

Richard Roth

The FixYa Team

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

April 8 2002 DIV 26 SOURCE 110 KENMORE ELITE HE3 & HET WASHERS "ADD-A-GARMENT" INDICATOR LIGHT ON DOOR WON'T UNLOCK WHEN PAUSE/CANCEL BUTTON IS DEPRESSED.

MODELS: See additional page for Kenmore model numbers

COMPLAINT: Due to a Microcomputer Machine Control software error , the ADD-A-GARMENT feature becomes inoperative.

CORRECTION: The Microcomputer Machine Control must be replaced with a service part that has been reprogrammed to prevent ADD-A-GARMENT feature loss.

PARTS: Order electronic control listed on this service flash by model from Division 26 , Source 110 following normal ordering procedure.

MERCHANDISE CODES: WASHER Service Flash - Model Nurnbers for: Kenmore Elite HE3 & HE3t Washers: "ADD-A-GARMENT" indicator light on door won't unlock when Pause/Cancel button is depressed. Kenmore models with serial Numbers beginning with CSL23 through CSM04 11042822200 11042824200 11042826200 11042832200 11042834200 11042836200 11042922200 11042924200 11042926200 11042932200 11042934200 11042936200 Electronic conrrol p/n 8181900 Electronic control p/n 8181899



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

HI. this code represents a Long Drain issue.

If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects(located, and mounted on the actual pump)
• If the above does not correct the problem replace the pump

I have a Kenmore HE5 Steam: after a power failure last week, now when you turn the dryer on and push"start" the cycle stops emediately and flashes PF...

I have an H3 washing machine and the rubber bellow lip that seals the front door from leaking has torn causing water to leak out. Can this bellow be repaired or easily removed and replaced without calling a service repairman.

I am getting an F35 code on the washer has anyone had this problem