DEI Python 1400XP Remote Start/Keyless Entry System - Answered Questions & Fixed issues

email sent

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U get free manuals

The automated lighting has ambient light sensors and an electronics package that can cause similar issues when they fail.

Properly installed remote starters rarely interfere with normal operation of a vehicle. There can sometimes be an issue with the security module that interfaces with the vehicle anti theft. Although rare it can be diagnosed easily. Most often is the vehicle security system components found to be degrading overtime causing intermittent issues. Passlock, passkey 123, pats, all have their own unique component failure issues.

check your starter they act up like that, when it will not start if you could try to hit it with a hammer, pipe anything you can not on the solenoid but on the body of the starter if it start up you know that is your problem.

If you have an alarm, or remote start with an alarm, you need to press and hold thethe valet button which would be hidden under the dash on the driver side, as you are turning the key sometimes remote starts have a starter disable or an alarm option to reset it that is what needs to be done, some systems even if you dont have an alarm go into a valet mode if your remote battery is old or you never reset it or the alarm kicked in or what have you. if this does not work for you then you will need to bring it to a dealership and have them do a total reset to the computer you can also try disconnecting the negative battery cable, but do this with the door open cause it will reset everything, and google the reset procedure for the key fob (remote).. do that reset for the remote and it should save you money from having to bring it to a shop or dealer.
hope this helps.

At this point in my life, I don't know what I would do with out my car remote. It should be an auto electrician that installs the system. As for the program, I am not sure. You might need to look further into it. Elisa Jed ' http://www.stevemacautoelectrics.com.au/services

It sounds like the alternator is bad. Remove it and have it tested before replacing the battery. If you need further help, reach me via phone at https://www.6ya.com/expert/scott_843b43f7ebebd3f5

google it

Tools: 10mm torque wrench Step 1: Find the release bonnet lever or button in the car. Step 2: once the bonnet is open, locate the battery pack. Step 3: Then locate the negative charge and unplug the connector to the terminal by using your torque wrench. Step 4: Then replug it in and close Start the car up and it should work. Hopefully it works.

go back to installer for reset guidlines

Possible chip in key bad security prob

Here is the link for Python 1400XP Wireing! http://rovertech.clanteam.com/depo/Python/1400xp_install.pdf

Year/make/model? Have you checked the reading from your intake air temperature sensor (IAT)?

Sounds like the bypass that was installed when the remote start was done lost programming, if you look under the dash and find some boxes under there reply back with some part #'s and I am sure someone can help you out.

If engine dies while driving and locks trigger then program your remote not to lock/unlock when turning on/off ignition. My car did that for a while before i figured it out and now my car actually runs 100% better and I've had no problems since.....

what wires is for rhe siren on my 1400xp python?

1. Locate the valet switch for your system. It's a small black push button, connected to a pair of wires that are gray and black. There's no telling where the installer placed it, or if he even left it connected. But if it's there and you find it:

2. Put your key in the ignition and turn it to the "on" or "run" position (not to "start").

3. While the key is on, press the valet switch once and release it, then press it again and hold it.

4. Press the "lock" button on the key fob.

5. Release the valet switch and turn the key off.

6. Test the key fob to see if it worked.

474P. Additionally, the 474T, 474V, and 474L will also work.