20 Most Recent Canon imageCLASS MF7480 Laser Printer - Page 2 Questions & Answers

It's the code for paper jam. Open up the lids to see if there is paper stuck anywhere.

6A00 Is the code for a paper path feed error. this is sometimes caused by the purge unit becoming clogged with debris. The purge unit sits underneath the cartridge print head and is designed to keep the ink flowing and clear. Turn the printer on, lift the lid so the cartridges move to the center and turn off. Look where the cartridges normally sit and you will see a sponge housed in a plastic frame. Move this frame back and forward, remove the cartridges and replace them, then turn the printer back on.
If this does not solve the problem then unfortunately a replacement printer of a service call to canon is un-avoidable.
I hope this helps Regards GM

90% have saved an object in the printer,must undo to remove the foreign body.

Hi,

Welcome to Fixya. If you need the instruction manual on how to operate or change the ink on the Canon ImageClass MF7480 you can refer to the link below it also includes the driver and software of the machine.

Canon ImageClass MF7480 Support

If you have questions please let me know. Thanks for using Fixya.

here is the link. It's a pdf file so you must have an adobe acrobat installed in your system before viewing this manual
http://gdlp01.c-wss.com/gds/0/0300001870/01/MX320_GS_EN-US_V1.pdf

How to clear Error Code Canon printers MP150 MP160
CANNON Printers
Unplug the printer for at least 2 minutes from the wall.

2. Plug the printer back in but leave the printer turned off.

3. Enter Service Mode

a. Hold Stop/Reset button and the Power button for 5 seconds

b. Release Stop/Reset button but continue to hold Power button

c. Press Stop/Reset twice

d. Release the Power Button

e. Wait for the light to stop flashing. The printer is now in service mode. The display may be blank or simply read "Canon" during this time.

4. Do an EPROM reset.

a. Press the Stop/Reset button 3 times.

b. Press the Power button twice. The printer will save the changes and then it will reboot. A little cd/dvd icon will appear in the LCD screen.

3. The printer will probably now require the same setting up as when you first unpacked it. That is, you will need to select a language and let the printer do a head alignment.

The printer is now enabled.
MP150/MP160 ERROR CODES:
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD over current error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Test the cables.

USB cables uses to fail without advise.

If you are connected by parallel cable, replace it.

If it is connected by Ethernet, make a ping to the ip address of the printer con see if there is phisical connection to the printer.

http://www.usa.canon.com/cusa/consumer/products/printers_multifunction/photo_all_in_one_inkjet_printers/pixma_mp560#BrochuresAndManuals

try these steps:

Setting SNMP on the Device SNMP helps monitor the state of the machine and collects information on it. The following items can be set:
<Community Name>: Sets the SNMP community name. You can specify up to two community names. <Writable SNMP>: Enables the computers on the network to access the machine and modify its settings if this item is activated. You can specify this setting for each community separately. <Get Printer Management Information from Host>: Enables automatically the SNMP port monitoring function to obtain printer management information such as information on print applications and printer ports, if you are using Windows Vista and set [Standard TCP/IP port] for the printer driver port. 1. Press (Additional Functions).
Press (Additional Functions). 2. Press [System Settings] [Network Settings] [SNMP Settings].
If the System Manager ID and System Password have been set, enter the System Manager ID and System Password using - (numeric keys), then press (Log In/Out) to enter the System Settings menu. The SNMP Settings screen appears. 3. Select [On] or [Off] for <Use SNMP>.
[On]: When you set or browse each item of the machine with utility that uses SNMP to obtain information. Proceed to step 4. [Off ]: When you do not use an SNMP utility. Skip to step 7. 4. To change Community Name to a name other than <public>, press [Community Name], then enter the community name using the touch panel keyboard.
5. Select [On] or [Off] for <Writable SNMP>.
[On]: Allows the computers on the network to access the machine and modify its settings. [Off ]: The computers on the network cannot access the machine and modify its settings. 6. Select [On] or [Off] for <Get Printer Management Information from Host>.
[On]: Enables the SNMP port monitoring function to automatically obtain printer management information such as information on print applications and printer ports if you are using Windows Vista and set [Standard TCP/IP port] for the printer driver port. [Off ]: Disables the above function. 7. Confirm the settings you specified, then press Turn off the machine, wait at least 10 seconds, then turn it on. [OK].
8. Press [Done] repeatedly until the Additional Functions screen closes.
9. Restart the machine.
Turn off the machine, wait at least 10 seconds, then turn it on.

This was very difficult to find, but I found it just for you! Please make sure you rate my answer 4 thumbs up! Thanks so much for understanding, it would be a huge help to me. Here is the manual / guide, it is quite large so give it a few minutes to load once you click on it:

http://micromatikal.dlinkddns.com:8000/cust/MP980.pdf

Firstly have you downloaded the latest driver from Canon's website?
Secondly I suggest you uninstall the printer, disconnect the data cable to the
printer, open the Printers applet in control panel and select File/Server
Properties and click the Drivers tab. Then remove any and all drivers for the
i860. Now run the installer and plug the data cable into the printer when asked
to. See if that helps.
My concern is that if the test page is good then it may not be a printer
problem but removing the old driver from your system as detailed above is well
worth while.