20 Most Recent LG 24 in. LD-12BW5 Free-standing Dishwasher - Page 4 Questions & Answers

Hi,
Check to see what is working or running when it is making the buzz...is it when the water is coming in ...then it would be the soleniod coil on the fill valve...
if it is when it is washing, then it would be the motor going bad...
if it is when it is draining, then it could be the pump if you have a separate one or it could be a soleniod that directs a flapper to run the water out...
lots of possibilities...

heatman101

Thanks for your question!
I'm sorry that you haven't received an answer yet.
The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...
Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.
Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.

Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!
If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

I need operating manual of LD2131SH, thanks

Hi


Thanks for using FixYa. Error E1 is a leakage error which occurs due to excessive RPM of washing motor during wash cycle due to water leakage. This is caused due to either water leakage in hose, the motor water seal is leaking and/or the impeller of the washing pump is worn out. To resolve this issue you’ll have to check the point of damages and repair/replace the part that has gone bad. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

A small label like that shouldn't be the problem the motor may have just burned out. if it still sprays then is a solenoid that changes the valve to pump out. If it doesn't spray you may have a more serious issue.

Hi, use this table to find and know more about codes.When you get into the link,scroll you will see all codes and solution.

(repairclinic.com/0078.asp).

Take care.

Hi.

Regarding the fill problem, the electronic control board rarely fails in the way you described.

When filling stops beforetime in the cycle, this is caused by the water level sensing device.

Before replacing the timer board (that is probably faulty), the water level switch must be tested, disconnecting power and wiiring and reading Ohms to ensure that the switch is opening and closing, or by jumping the switch and controlling the cycle manually to prevent overfill.

To get parts and schematics see: Where do I find parts and diagrams?

Regards.

OE is OUTLET ERROR.
More often than not, a blockage is in the pump(not that easy to get to and quite a long step by step process)
You might also find the blockage at the end of the drain hose, where it connects to the drain pipe- remove the hose clamp and inspect hose and spigot.

Hi,
Test to see if the machine is heating water. If not - replace the heating element, then the thermostat if still not heating.

If the heater is ok, then it is the control board at fault, requiring replacement or repair.

Hi


Thanks for using FixYa. HE error is you dishwasher means “Heater Error”. This is caused when either the heating element or the thermistor goes bad as the thermistor is also part of heating assembly. To resolve this issue the heater assembly should be replaced or whichever has gone bad out of two (heater/thermistor) should be replaced. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Hi,
Here is a tip that I wrote about leaking dishwashers

http://www.fixya.com/support/r4546178-leaking_dishwasher

heatman101

These are all site replaceable. Contact the company service provider.

If board has to be replaced only the Company can help you with the correct board.

"HE" is a "HEATER ERROR"

These are the possible causes for "HE" error:
1. The Circuit of Heater is troubled.
2. The Thermistor is troubled.
3. The Heater is shorted.
4. The Relay Circuit is troubled.

The Possible solutions are:
1. Repair the Circuit of Heater.
2.Replace the Thermistor.
3. Replace the Heater.
4. Repair the Relay Circuit..

E1 Leakage error. Cause : water leakage in hose connections. Water is leaked by damages.

Hi,
Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drilled out large enough. This then causes a blockage. Also check the non return valve under the filter and make sure the drain pump can turn freely.
Hope this helps.

Hello,
You probably got a power surge that burnt out the coils in the water soleniod valve. This tip will help you with replacement.

http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_entering

Heatman101