Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven - Page 5 - Answered Questions & Fixed issues

Okay,
1, check your power, locate your breaker for the range. turn the breaker off and turn it back on.
Your Range it is electronic control on the Oven but not the Stove Top heating elements.
After you reset the breaker and it still not work.
Please let me know more about the unit.
When you purchase.
How/when it happen.
What is the indicator showing.

[email protected]

The switch contacts have welded closed and you must replace the switch.

shut the power off for 30 mins at circuit breaker and then it worked after that.

Yes needs a new element.they burn out. easily.you know this because they sell them seperately.its there way to make money off of you.anytime they sell you something and the parts are readily available especially sold seperately you know its going to need to be replaced eventually..If you replace 1 replace them all to avoid furthur issues.

This is failed communication between the EOC and the temp sensors located in the oven. i recommend testing the EOC(break point test on the pins) for its operational value and the temp sensors as well. replace any component that doesn't register.

I would also inspect the oven temp sensors for welded harness and fouled housings.

In most cases, this will be a EOC issue.

If both elements are not working properly then the problem is either the temperature probe or the control board.

Replace the temp probe first.

Frigidaire / Westinghouse / Tappan / Gibson
Oven Fault Codes
Display Condition Remedy
F0 & F1 EOC failure Replace EOC
F2 Oven over heat Defective Sensor or EOC
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it
F5 EOC failure Replace EOC
F6 EOC failure Replace EOC
F7 EOC failure Replace EOC If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Sir,
Check out this link

suggest to reset it by shutting off both main breakers to the stove , wait for one minute and switch breakers on again.

Thanks Good Luck
Appreciate to rate as "Fixya"

F9 code means Control has detected a problem with the motor door latch assembly Soultion: Check wiring, replace the motor door latch assembly if necessary

do have the the seting set to air dry? or possible a sensor issue or maybe the heating element at the back has not bee connected or has shorted

i would say its a wiring issue so i would have to turn to the repair man

u can go to there site or type in the model numbers and/or the model it self and after that typ manual and it should come up on the intranet

Hi, i would check the pressure switch and its connection as well. either the switch is malfunctioning or the wires and connectors are corroded. simply replacing the wires or switch will fix this issue. the switch is usually located on the rim of the inside of the oven door. it will make contact with the oven door and as the oven door closes, the pressure switch is depressed inwards, thus, opening the circuit and cutting power to the light.

Please rate and god bless:)

test

i called my brother and he came over and fixed the problem.

Whithout knowing the model number in general it takes several hours for the cleaning cycle. My oven takes approx. 4 hours to complete a good cleaning. On my own oven, you can set the timer for as long as you want. Do you have an owners manual? If not, you can find one here...........
http://www.frigidaire.com/support/manuals.asp

The oven has a small button on the left side on top of the control panel. Switch it on or off. Hopefully this will solve the problem.

Parts Schematic and wiring diagram. https://www.partselect.ca/Models/CGEB30S9FB3/ Part F161 is the Convection Element. Check it for continuity with a multimeter and also check the connection tags to it as they can melt. https://www.partselect.ca/PS2361497-Frigidaire-318255504-ELEMENT.htm?SourceCode=20&SearchTerm=CGEB30S9FB3&ModelNum=CGEB30S9FB3&ModelID=899380 ..

Fan speed Tacho https://www.google.com/search?q=Frigidaire+Gallery+double+wall+oven+is+throwing+code+F+43 ..

If the display is blank then I would assume that the power board is dead and will need to be replaced