20 Most Recent RCA HD52W59 HDTV Projection Television - Page 9 Questions & Answers

supertruc195,

See my tip at http://www.fixya.com/support/r6396176-projection_tv_troubleshooting for troubleshooting help.

Thanks for using FixYa and for the great rating.

hardrocko

Use your cable or satellite tv remote to adjust the aspect ratio. If you have cable there is a button on the remote called hd zoom and it has this symbol: #. On the satellite tv remotes it usually says format or aspect. You might even have to go into the cable box/satellite tv receiver menus to adjust the aspect ratio/picture format. Once you have done so you can fine tune the picture even further with the television remote's wide/format/aspect/zoom button. Also check and make sure your television is on the right input and that your cable box/satellite tv receiver is set at the right resolution for the television 1080p/1080i/720p.

Can you describe what you mean when you say out of Phase? is it a convergence issue ( 3 D appearance) or a picture issue such as rolling vertical or Horizontal lines?

The flyback transformer could have bad solder joints around its mounting pins. I would try resoldering the flyback transformer.

Problem will be on the Deflection Board, something is shorted in hori circuit.

PTS rebuilts boards 1-800-844-7871

Replace the deflection board very common issue with that model. You can get replacement Deflection boards from www.tvrepairworld.com

Replace the deflection board. The deflection board is famous for having various issues. You can get a replacement Deflection Board from www.tvrepairworld.com

Adjust the ZOOM Control.Look in your Menu under settings.

mcnamara724,

Bad convergence circuit. See my tip at http://www.fixya.com/support/r4220499-change_projection_tv_convergence_ics for repair help.

Thanks for using FixYa and for the great rating.

hardrocko

Problem will be in the Deflection board,Located on the bottom left handside it will have FBT flyback Transfomer on it, check Capacitors CP150, CP120, CP114. If CP 150 is Swollen or vented on Top the replace all 3 caps.2200uf 16v use 25v, 220uf 35v.
You ship board for repair to PTS 1-800-844-7871
These sets are also known for having Bad FBT flyback Transfomers and alot of Poor Solder Connetions

It owes to that a problem has in the feeding source of his tv or the screen this fall or exhausted

kelbril2000,

You have a problem on the board which controls the unit. It is the small signal board. Part number 268850 (for models Yx38 - Yx39) or 268851 ( all models except Yx38 - Yx39). The boards are available at http://www.encompass.com for $170.00 plus shipping. Go to the site and enter as a guest. Put the correct number in the part search engine and order the part. I have a tip at http://www.fixya.com/support/r6981868-replace_circuit_board_in_modern_tvs which should help with getting the old board out and installing a new board.

Thanks for using FixYa and for the great rating.

hardrocko

Replace the deflection board. You can get one from www.tvrepairworld.com

Hello,

It's the problem of overheating in the power supply board of the TV.on the power supply board of the tv there are few capacitors and IC.any of this ic is got short or may be weak.so due to this when you start the TV the current passes from electric outlet to the power supply board of TV.but when the current passes from that weak/faulty part at that time current gets stopped or slow and the board overheats and TV shuts off. this is a common problem faced by many other users too.the possible option to solve this issue is to check the power supply board by a meter and continuity tester and replace the faulty component on the board which is short due to which power supply board is getting overheated.its bit technical job but yes its not at all a costly repair to do or get it done by the technician. for required parts it can be easily available from local electronic hardware shop.

Hope this will help out.....

sounds like you blew a power resistor its a big white block if you keep turning it on you will burn your board beyond being repairable. the deflection board is very rare only one repair service exist on ebay.

Sounds like the CRT has an issue which is shutting the other ones down. Try removing the CRT drive board from that one CRT and then try to power up the set. It should stay running with the board remoded and just hanging. If it does you will know that CRT needs replacement. You can get a replacement CRT from www.tvrepairworld.com

akiona,

This could be anything. See my tip at http://www.fixya.com/support/r6396176-projection_tv_troubleshooting for troubleshooting help.

Thanks for using FixYa and for the great rating.

hardrocko

Go to setup , and conversion settings. set convertions.If it wont set correctly you must replace or let it been replaced by tech. If you are a tech you can set convertions manualy by go in to service menu. It takes sometimes up to 4 hours to set. But remember to save.

The green CRT most likely has an issue.

Thats almost always caused by the deflection board having an issue. You can get a replacement deflection board from www.tvcircuitboards.com