20 Most Recent Minolta bizhub 200 All-In-One Printer - Page 3 Questions & Answers

Magenta PC Drum Motor. Pull out the magenta image unit and replace it with a new one Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sir could not find that code for a Bizhub 200 service manual please recheck Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Lower temp on the fuser. To reset. on the right side of the machine just below the scanner section (The part with the big glass) is cover next where you connect the Ethernet cable. Remove the cover with machine on use a small screw driver and gentle depress the small black switch the machine is going to go thru some screens when you the screen with copiers on it to the left on the screen in the middle you will see a "." when that is displayed press 3. Code will come back but now press the Utility/counter button should see button that say maintenance mode press that see trouble reset press that machine again will go though warm up procedure will see the "." DO Nothing!. Should go to "Ready to Copy" if the code comes back have a technician look at it DO NOT CONTINUE TO RESET the code is for the Hot Part called the FUSER. can catch on fire! That will ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Elevation drive problem for the finisher exit trays. Requires removing the rear finisher cover remove the elevation drive motor assy. BE CAREFUL FREE FALLING TRAYS!!!!!!!!. Then reset the position on the trays to align to the exit sensors below the orange rollers and remount the motor assy. DO NOT STORE BOXES OR TRASH CANS UNDER THE TRAYS Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You can try konicaminolta web site drivers are free. But Di5510 I believe best you can do is XP or windows 95. But give the web site a try. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Remove the first draw check for paper behind it. Then remove the paper that is stored on the left hand side . That is not a storage area its for when you want 11x17 paper placed in the draw. If that does not clear the code the motor or the sensors that monitor the tray are bad or worse the control board is bad. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

No such code for that model machine Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Go to konicaminolta web site to get drivers for free Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Remove the second draw and remove the paper from behind it. Then remove the extra paper in the second draw that is sitting on the left hand side that is not A STORAGE location . It is for 11x17 paper. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

What code is the machine giving you? What is the problem does not print does not copy ? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Could not find that error code for a Bizhub 200. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

No such code for a Bizhub 200! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

There is no waste toner box on a BIZHUB 200. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Is this machine on a network? if so can other computers print?(IF others can not the machine) If this is a single computer are you using a crossover Ethernet cable. Are you sure the proper drivers are installed go to Konicaminolta to get latest drivers free. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Utility counter, details stop00 stop01. Counters. Has the drum been replaced? if not you reset the counter the machine will assume that a new drum is install and select the proper voltages for a new drum since the drum is not new? it might code and get poor image quality issues. Replace the developer with the drum. Machine uses the counters to determine setting in the machine, developer also has a counter. Does the front panel say replace PC drum? If so replace developer and drum and cleaning blade at the same time. You clear counters before pulling out the image unit. and you don't exit all the way out of service mode after clearing the counters you hit exit once the turn off main power, Rear left side. Once new drum and developer installed. RUN F8. Do not allow copies Prints or fax until F8 is run. Or start all over again. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sir/ma could not find that code for a Bizhub 200 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Print head failure The assy. that has the machine LASER inside of it also has a motor called polygon motor very high speed 35000 plus rpm. mite hear when you turn on the machine initially . Well it causing the code. Open close front door to reset Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

PULL out the second tray remove any and all paper from behind the draw also REMOVE all the STORED paper on the left hand side of the draw that is not a storage area. Storage draw is used. The space is for if you decide to 11x17 paper Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

OPEN first draw remove the paper from behind it Then remove the paper that is being STORED ON THE LEFT SIDE. DO NOT STORE EXTRA PAPER ON THE LEFT SIDE that is what the storage draw is for. The reason there is that space is if you plan to use 11x17 paper for something Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Could not fine the code 6102 for Bizhub 200 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f