Hyundai ImageQuest LM1510A 15 in. Flat Panel LCD Monitor - Answered Questions & Fixed issues
On a 2009 Hyundai 1.6 on the chains how many links separated the 2 cams
are you sure that it is a 1.6 motor
as 1.6 motors use a belt not a chain
your statement that it has 12 on each cam indicates that it is a v engine or a double over head engine
in any case you do not count links but put the colored links directly over the sprocket dots
you have to use a cam locking tool to get it right
8/3/2018 12:28:43 AM •
Hyundai...
•
Answered
on Aug 03, 2018
•
219 views
Remove monitor base
remove the cover on the back of the base and remove the screws that hold it on to the monitor.
5/11/2013 7:21:28 AM •
Hyundai...
•
Answered
on May 11, 2013
•
131 views
I am getting a message:
Hi,
This message ususally appears when a certain program has a requirement to run it. And if your display does not meet that, that is the time you will get this error message. Try to check the requirement of the software that you are installing and check your display information on the comptuer see if its conaptible.
Thank you for using Fixya. Your REcommendation is highly appreciated for the free support.
8/16/2011 4:18:36 PM •
Hyundai...
•
Answered
on Aug 16, 2011
•
120 views
After about 1 minute warmup
The problem you are describing is in the inverter board that powers the back lights behind the screen. The cause is bad capacitors in most cases and develop a bulge at the top indicating it is open. Repairs can be attempted or the board replaced.
3/19/2011 5:14:46 PM •
Hyundai...
•
Answered
on Mar 19, 2011
•
811 views
My WD passport is not recognized by my computer
It could be that you have a defective drive. Attempt to return the drive and explain that you believe that it is a defective product and ask for a replacement or a refund.
2/28/2011 6:32:16 AM •
Hyundai...
•
Answered
on Feb 28, 2011
•
117 views
Hyundaie gennesis seat position memory
Hi,
You have posted the problem under "
Hard Drives" section.
Kindly submit the question under
Hyundai Genesis section on the website by clicking this
link so that the best car experts can view and post a solution to the problem.
On the page which opens, type the question in the "
Ask an Expert" box on the right hand side of the page and click on "
Post a problem" button.
Thanks for using
FixYa.
1/30/2011 5:07:40 PM •
Hyundai...
•
Answered
on Jan 30, 2011
•
49 views
When I boot up my
One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect your hard drive
Test the leads that attach to your ((hard drive from the motherboard)) or replace all the leads that attach to your hard drive including electrical extensions + IDE,SATA and the ones that attach from your ((motherboard to hard drive))
make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electic extensions or just replace them they are probably old and faulty a computer needs its connections to have an end so any faulty leads will end up with a computer error
hope this helps
1/9/2011 9:47:56 AM •
Hyundai...
•
Answered
on Jan 09, 2011
•
122 views
I would like to reset
Turn Off the computer, now as soon as you hit the power button, keep on holding "Alt" key & keep on tapping "F10 key,ie: Alt+F10, it will open the recovery console ,select full factory restore and follow on screen instruction. (Note:this will erase all datas on the computer)
Hope this helps
1/3/2011 5:55:15 AM •
Hyundai...
•
Answered
on Jan 03, 2011
•
103 views
Need power cord for hyundaiimage quest model B9oD
You can find a replacement power adapter from your local electronics store, just bring the dead one with you so you can match up the correct voltage requirements and the bullet connector for the right size. If not try ebay, you will probably find a replacement on that site
10/29/2010 1:10:00 PM •
Hyundai...
•
Answered
on Oct 29, 2010
•
111 views
Would you please advise how to adjust the
Hi; the upper part of your keyboard closest to the screen or the last row of keys contains a BRIGHTNESS key...
Press and hold the Fn key (usually italic and purple color) and press the Brightness (sometimes depicted by a bright bulb) key and observe if there's a change in brightness...remember to hold down the Fn key while adjusting the brightness. I hope this helps since you did not mention computer type or keyboard arrangement!
1/23/2010 2:24:59 AM •
Hyundai...
•
Answered
on Jan 23, 2010
•
752 views
Not finding what you are looking for?