Top 20 HP PSC 1210 All-In-One InkJet Printer Questions & Answers

if the problem is not resolving read manual manual see if there is any guarantee ,if its not too old . Sometimes take out wallconnector , a cannister of compressed air to clean something inside, If microswitches are used or an opto coupler , sometimes a new printer is cheaper then repair A very little suggestion sometimes you have luck by Youtube without commercial costs. Out of Paper Error Displays and the Printer Does Not Pick Paper in All in...

Hi, I suggest a informative link supported please visit and read it.. Block Unwanted Junk Fax Numbers and HP Printer Support + Thanks,

You need to download the appropriate drivers on your Mac to allow it to understand how to talk to your printer. This is described at the HP website: http://h30434.www3.hp.com/t5/Printer-All-in-One-Software-Drivers/Printer-HP-PSC-1210-All-in-one-driver-for-Mac-OS-X-10-9-4/td-p/4092240 The link above will direct you also to Apple to download the generic HP driver: http://support.apple.com/kb/DL907

carrige unit error

I think Paper try sensor not working properly. Check the sensor, is it on normal position?

Hi, If you are given print command and that time printer off position no issue, because print command given after on the printer then printer seance any command or printer print the doc. Thanks,

I checked the manual, the image of the face of the calculator and there is no way to change the entry mode from RPN to Algebraic. Your calculator is still in RPN, it is the only mode it has. Reset it.

scanning xray film is not possible in this model. you need a negative scanner to do that.normally in software you have an option called negative. this option convert the positive image into negative. but it will not give exact output what we need. you can try this option also.

please copy " hp psc 1210 driver OS " change OS with your operating system

is it pluged in,if so there are a fuse inside that might have blown.

HP Printer Packages http://h20000.www2.hp.com/bizsupport/TechSupport/ProductList.jsp?lang=en&cc=us&taskId=135&prodTypeId=18972&prodSeriesId=25523

how to change language chinese to english

Follow the steps to align newly installed cartridges.

• When prompted, make sure plain white letter or A4 paper is loaded in the input tray.

• Press the button next to OK on the control panel display.

• The product prints an alignment page.

• Place the alignment page print-side down on the right front corner of the glass.

• Press the button next to OK on the control panel display.

When the On button stops flashing, the alignment is complete. Remove the page and recycle or discard it.Method two: Print an alignment page using the computer

• Double-click the HP Digital Imaging Monitor icon ( ) on the lower right side of the Windows taskbar.

• The HP Solution Center displays.

• In the HP Solution Center, click Settings . Then click Printer Toolbox .

• The printer Toolbox displays.

• Click the Device Services tab.

• Click Align the Print Cartridges .

• When prompted, make sure plain white letter or A4 paper is loaded in the input tray.

• Press the button next to OK on the control panel display.

• The product prints an alignment page.

• Place the alignment page print-side down on the right front corner of the glass.

• Press the button next to OK on the control panel display.

When the On button stops flashing, the alignment is complete. Remove the page and recycle or discard it.****If you need any technical help on printer then you can reach at http://www.vtechsquad.com/

TYR TO POWER OFF PULL OUT PAPER THEN BACK ON & PUT PAPER BACK IN,.

Hi,'What is the Windows operating system you are using ? Like is it, Win XP, Vista or Win 7 ?If you are using PSC 1210, My suggestion would be to uninstall and reinstall the software using the same disk you have for the printer.Regards,Sean

what type of file boss and which error it shows can u explain more plz

http://www8.hp.com/us/en/support-drivers.html?pageDisplay=drivers

In Windows-based systems, you open the Printers and other peripherals folder. Point to your printer with the mouse cursor and right click. In the drop down window that opens check the seb-menu option MAKE DEFAULT.

Hi Sean,How do you want to connect your printer to PC ?Please provide the below information ?What is the operating system on your PC ? How do you want to connect your printer ? via USB or WirelessIf you are using Windows 7 PC, you dont need drivers for your printer as HP does not have it designed,You can connect your Printer to PC thru USB Cable directly and the drivers will be loaded.Regards,Suhail