20 Most Recent Intel Motherboard - Page 10 Questions & Answers

Hi,
I am looking for the site for a Bios update to my eSysy PC.
The motherboard is stamped as an eSys P4M800/775 V3.01 and Sisoft etc confirms this but so far it is impossible to track down the manufacturers site.

http://www.youtube.com/watch?v=HZ5w3ZUC_5khttp://www.computerhope.com/jargon/s/spc.htmabout frontpannel-connections in general.

The display was damage or the power is not reach to the display.buy a new display

TRY THIS.GO TO SERVICES AND RESTART WINDOWS AUDIO.

1.CHECK THE MONITOR.2.CHECK THE CABEL FROM THE MONITOR SHOULD BE SEATED TIGHT ALSO IN THE VGA-CONTACT.

Do you have a question?

hi

this is the manual for the system that this board is from

http://download.lenovo.com/ibmdl/pub/pc/pccbbs/netvista_pdf/24p2969.pdf

I hope this helps

NetVista types 8181, 8182, 8301, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, 8315

in models
21U 21F 22U 31U 31F 31G 32U CTO 23G 11G 51U 51F 51G 52U 52S 52P 53U 53S 53P 61U 61F 41U 41F 54U 54F 54S 54P 81U 81S 81P E1U E1F E1S E1P 41G

plzzz give me a soud drivers.this is my e mail [email protected]

Not knowing your exact model, here is a link to one of the 845 MB driver sets

http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&ProdId=757&DwnldID=15500&lang=eng

Does it have a serviceable power supply connected? Does it have a keyboard connected? Is it in a case? Does it have a processor and heatsink/fan connected?

Hi

I like to download this drivers for my computer
PWA, 62YVH Rev A00

Kind Regards
Phumlani

http://www.the-manuals.com/msi-n1996-pdf-manual/

E2160 IS A PROCESSOR

http://support.gateway.com/s/MOTHERBD/Shared/4006157R/4006157Rmv.shtmlhttp://support.gateway.com/s/MOTHERBD/Shared/4006203R/4006203Rtc.shtmlOpen in two different windows.The Top link is for a clear photo of the motherboard, and the letter designations.The Bottom link is a navigation guide for those letter designations, HOWEVER they do NOT match up. I will guide you using both links.1) Go to the Top link - Main ViewLook at the right side for letter R.This points to the 24-pin ATX main power cable's connector, on the motherboard.In the second link - Hardware Details - it is letter J- Main Power ConnectorThis is a general example of a 24-pin ATX main power cable, and it's respective connector on the motherboard,http://www.playtool.com/pages/psuconnectors/connectors.html#atxmain24(NOTE* Color never matters)Note that there is a Lock on the side (Middle), of this main power cable's connector.There is also a matching Tab on the motherboard connector.To remove this power cable the top of the Lock is squeezed in. This action brings the Lock's hooked end away from the Tab, on the motherboard connector.The Lock operates like a see-saw on a playground.2) Go towards the Top/Middle to the letter C, in the Main View.This points to the 4-pin ATX +12 Volt power cable's connector, on the motherboard.In the Hardware Details it is the letter C also.C - Auxillary 12V ATX ConnectorThis is a general example of a 4-pin ATX +12 Volt power cable, and it's respective connector on the motherboard,http://www.playtool.com/pages/psuconnectors/connectors.html#atx12v4Note that it has a Lock, and the motherboard connector has a Tab, also.That's it for power cables TO the motherboard.3) Since there is only one IDE (PATA) connector on the motherboard, I'm going to assume you are using a SATA harddrive.Uses a SATA power cable,http://www.playtool.com/pages/psuconnectors/connectors.html#sataNote that a SATA power cable's connector has 15 contact pins.Between it, and a SATA data cable's connector, the SATA power cable's connector is longer. Note also the L shape inside the connector. There is also a Lock tab you depress on the cable's connector, when unplugging it.4) General example of a SATA data cable, and it's respective connector on a motherboard,http://en.wikipedia.org/wiki/File:SATA_ports.jpgYou can see the L shape a little better here. A SATA data cable has 7 contact pins.The connector shape usually used on the Harddrive, is a 90 degree bent elbow.The straight connector end is plugged into the motherboard's SATA connector.In the Main View the letter U is the SATA connector designator. Look to the left of the Front Panel connector, designated by the letter T.Those four Orange connectors are SATA connectors.The Harddrive usually plugs into SATA 1. In Hardware Details this is shown by the letter L.L- SATA ConnectorsLooking closely you can see the SATA 1 connector, is at the Bottom of the motherboard.However the beauty of SATA is, that you can plug the harddrive into any of those SATA connectors, and BIOS will find it.In the Main View the letter S on the right side, points to where a computer case fan plugs in.(Chassis Fan)The letter F in the middle, points to where the Processor (CPU) fan connects.J is for the Front Audio Connector. (Audio ports on Front Panel of computer)K is where a Card Reader would plug in.This is the kind of power cable a Floppy Drive, and a Card Reader uses,http://www.playtool.com/pages/psuconnectors/connectors.html#floppyL points to where the Firewire ports connect to.1394a.(IEEE 1394 Connector)The letter O points to where the Front Panel USB ports connect to.Going back to the letter T - Front panel Connector, in the Main View.Go to Hardware Details, and click on -M - Front Panel connector4 pins on the Left side, 5 pins on the Right side.The pins on the Left side are numbered EVEN.The pins on the Right side are numbered ODD.Starting at the BOTTOM on the Left side, going towards the Top;Pins 2, 4, 6, and 8. No Pin 10.Starting at the Bottom on the Right side, going towards the Top;Pins 1, 3, 5, 7, and 9.A) Pins 1 and 3 are for the HarDDrive activity LED. (Light)Pin 1 is for the Positive ( + ) wire.If the HDD LED is dim when the harddrive is active, switch the wires around.B) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.C) Pin 9 is N/C. Not Connected. 5 Volt test for the factoryD) Pins 2 and 4 are for the Power On LED. (Light)Pin 2 is for the Positive ( + ) wire. If the PWR LED is dim when the computer is on, switch the wires around.E) Pins 6 and 8 are for the Power On switch.For additional questions please post in a Comment.Regards, joecoolvette

no diplay in this board give me sme notes to chag ic.what ic i did change