Top 20 Nordic Track NordicTrack C2150 Treadmill - Page 7 Questions & Answers

see this The most likely cause of the problem is a worn treadmill belt and deck. Most of the time its caused from not lubricating between the treadmill belt and deck. This causes friction and the surfaces wear putting greater stress on the electronics. The treadmill is shutting down to protect the electronics. You should stop using the treadmill and have a technician check it.If it sounds like metal rotating on metal then it could be roller bearings or motor bearings. Its best to have the treadmill work carried out by a technician in the workshop. Most of the time the bearings will have to be pressed out and the new ones pressed inGod bless you

https://www.audiusa.com/content/dam/audiusa/brochures/2019/2019_Audi_Q7_QSG.pdf

please LUBE the deck belt+rollers bearing front and rear+test the drive belt motor, and replace if necessary. see the video attached.God bless you

please RUN the software calibration and fix it.God bless you

The Steps for Newer Style Console Calibration

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

see the video attached and fix it. God bless you

1) replace the batteries by new ones, with the same type, and polarityclean the contacts batteries v. well2) tight the ribbon cable from keypad , clean it and tight the connector.3) Adjust the REED SWITC H, see the diagram attached. clean it. test for open or faulty. Tight the conector very well.God bless youG

please LUBE the deck belt + rollers bearing too. See the video and proceed according. This happen because the lack of maintenance schedule.If after you fixed the problem remain , is TIME to replace the old board deck.God bless you

Try this website, please:http://www.livestrong.com/article/410922-the-controls-are-not-working-on-a-nordictrack-treadmill/

1) adjust the REED switch , see the diagram, clean it and tightthe plug very well2)test the fuse+ c.breaker see the diagram , replace or reset2a) test the main switch for open or faulty and replace3) if after this the problem remain.4) you have problem with the power supply:capacitor, transformer, diodes,etc Replace the main boadsee the block diagramGod bless you

I not shure , but you can try it with software calibration-However you can get answer more explicit from company via chat or phone. contact themGod bless you

1) Lube the deck belt, this happen because the electronic system protect the system and shut down.the cause is deck worn.2) Lube the rollers bearing too.3) Measure the input voltage motor, if there are the motor need repair.4) Measure the output voltage board, for input voltage motor, if there are Not the board is faulty.God bless you

please see the video and proceed according with common sense.God bless you

You need to call Icon ASAP and get a tech out under warranty to fix the issue.

1) Lube the elevation motor, see the diagram, parts gear + shift2) adjust the POT, for a little and see if there are better improve.3) RUN the software calibration for diagnose, troubleshooting, fix it.God bless you

cleal the contacts relais, and replace if necessary. Of course your LUBE the gear and shaft too.Test the elevation motor for problem bearing for repair.sincerely. God bless you

Lube the treadmills deck belt inmediately2= lube the rollers bearing too3=measure the input voltage motor, if there are the motor need repair4) measure the output board, for input voltage motor, if there are NOT the board is faulty.God bless you

see the video: God bless you

1) Lube the deck belt, this happen because the lack of maintenance according with the instr. manual. This produce shut down, for to protect the electronic system. Maybe you have a worn deck belt.3see the video and proceed according. LUBE the rollers bearings too.3) test the input voltage motor, and if there are voltage, the motor need repair.4) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the diagram attached.God bless you

go www. fitnessrepairparts.com or www. treadmilldoctor.com and buy it.or go to www. nordicktrack.comGod bless you

1) you must LUBE THE DECK BELT+ ROLLER BEARING.2) Test the input voltage motor, if there are the MOTOR is faulty need REPAIR.3) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty. 4) SEE THE BLOCK DIAGRAM, whatever component can be faulty.However you must test the power cord for short circuit between cable, repair, and look inside according the BLOCK, and proceed with logic, see any loose wires, or some wires touching the carcase, some filter, coil, power supply USE the VOM. God bless you