Polaroid FLM-2601 Television - Answered Questions & Fixed issues
What would cause no 24v power from power supply?
Hi aqhnc,
You need to change the whole power supply unit. Your transformer inside it might broken and need to fix.
I hope my solution may help you.
Thanks for using Fixya...;-)
5/6/2014 4:01:36 AM •
Polaroid...
•
Answered
on May 06, 2014
•
79 views
How put the cable in my tv for antenna
if you have an external antenna on your roof, then you would need to connect the antenna "Ant." (coaxial) If you have to old style 2 wire setup, you will have to get an adapter.Page 8 of your manual shows the connection it at the top-right of the TV's rear......
9/4/2012 11:43:08 PM •
Polaroid...
•
Answered
on Sep 04, 2012
•
158 views
My tv polaroid dose not turn on
check the power supply board for bad caps indicated by swelled tops. Thats usually the cause in most cases
6/20/2012 3:46:59 PM •
Polaroid...
•
Answered
on Jun 20, 2012
•
47 views
Won't power on....
I think I have the same problem, If I don't use it for a couple of days, then try to turn it on, nothing. I turn it off, and on one more time, it works. WEIRD
2/3/2012 3:34:53 PM •
Polaroid...
•
Answered
on Feb 03, 2012
•
167 views
My Polaroid fim 2601 will
hi did you mean when you turn on the unit the light indicator will flash but will not turn on until you plug and then re plug the tv unit the power will come out. now if this always be the problem just unplug first the unit to discharge excessive voltage at the primary capacitor of the power supply and to reset the error detected by the processor. now after an hour try to plug the unit and observe if the problem will not come out. if still the same problem you will need to open the tv unit now look for the power supply and replaced capacitors that bulged to its casing it was leak then the voltage will drop. you can found parts at
www.digikey.com replaced with same rating panasonic brand much better.good luck just give feed back to us if it is work i'm glad to help you.
7/15/2011 3:21:45 AM •
Polaroid...
•
Answered
on Jul 15, 2011
•
40 views
Wont turn on
Make sure it is plugged in.... Try a different outlet.... If it is plugged into a surge protector make sure that is on.... The surge protector may be set on a time..... The TV may be set on a time limit to limit the TV from turning on at different times.....
1/8/2011 11:40:18 PM •
Polaroid...
•
Answered
on Jan 08, 2011
•
242 views
Without any warning or any
This happens all the time with Lcd power supplies. You have bulged ( bad ) capacitors on the power supply board.
12/27/2010 4:51:33 AM •
Polaroid...
•
Answered
on Dec 27, 2010
•
99 views
My polaroid tv power light comes on but no picture
It can be bad 24vdc power supply for the backlight inverter board due to bad caps, or bad inverter board. You will have to do in-depth troubleshooting.
Try this first:
First, look at the screen in darkened room to see if you can see any slight glow from the screen, if it does, then the problem can be the T-CON (not getting the 12vdc) or the main logic board not feeding the signals to the T-CON board.
if not, next place to check will be the power supply module, make sure it has 24vdc which is required by the backlight inverter to work, the reason for not having 24vdc can be from bad DC filter caps (leaking/bulging top, high ESR) or short circuits in the inverter board which will cause the 24vdc supply to go into shutdown mode, so you may have to disconnect the power cable that feed the inverter board to see if the 24vdc will work without the inverter board hookup, you will need to apply about 3~4 amp of load to the 24vdc to make sure it can handle that. There are fuses on the backlight inverter boards also. So there is some troubleshooting you will have to do to find out the causes of the problem you are having.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:
Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums
http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Please post back what you find.
11/5/2010 3:29:54 AM •
Polaroid...
•
Answered
on Nov 05, 2010
•
93 views
I turn on the tv, and the light flashes to blue
The unit is in protective shutdown and without testing some of the components inside the set, there is little that can be done. I would suggest that you bring the unit into a service shop for a detailed repair estimate. Post the results here and we should be able to help you with the actual repair.
Dan
9/26/2010 9:36:02 PM •
Polaroid...
•
Answered
on Sep 26, 2010
•
57 views
Screen is black
hello,
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
CHANGED Z SUSTAIN BOARD.PICTURE PERFECT.APART FROM WHITE
DOTS..THINK IT COULD BE DUST OR FINGER PRINTS ON RIBBON JOINTS,,WILL RE CHECK
AND WIPE F/PRINTS TO SEE IF ANY CHANGE
5/23/2010 6:55:13 PM •
Polaroid...
•
Answered
on May 23, 2010
•
146 views
Not finding what you are looking for?