20 Most Recent Kenmore 43052 Front Load Washer - Page 2 Questions & Answers


Peace Friend,
ngfam1 At your service!

Things wear out! So is life!
Sounds like the coupling between the motor and the drum is broken! or the belt!!!
How old is the washer?


If the appliance is 10 years old or more you it may not be advisable to put good money into bad!
New appliances are so much more efficient today that they can save you a lot of money in energy!!!!
Water,Electric and detergent! And put money back in your pocket!
The new appliance will pay for itself in only a few years!

Only a trained laundry tech can make the electronic diagnoses.

Below I referred you to a great service nation wide!

If none of these tasks remedy the problem then here is a good company that's found nation wide.
A&E Factory Service
A&E has schedulers available to take appointments 24/7
And they do warranty work too, for most manufactures!
1(800) 905-9505

You will be fine
Bless You ngafm1
PLEASE GIVE ME A GOOD RATING BEFORE YOU SIGN OF

I

Kenmore 43052... | Answered on Sep 02, 2008


The big door seal is probably the problem. Put on gloves and using a solution of Laundry detregent and hot water and rags, carefully wipe clean all the folds of the seal. It will be icky. Next run a cycle with some detergent and oxyclean or bleach if you have it.

Especially during warm weather, damp clothing left in a front loader mildew slightly very quickly- you can't really see much but you can smell it! So get the clothes in to the dryer immediately. You'll want to relaunder the smelly clothing after you have cleaned the washer.

Good luck to you and Thank You using FiX YA!

Kenmore 43052... | Answered on Aug 20, 2008


please balance your washer and use smaller loads

Kenmore 43052... | Answered on Jul 08, 2008


bearing on most can not be removed there molded in the outer tub comes with the rear half of the tub already installed

Kenmore 43052... | Answered on Feb 27, 2008


You have to check your filter for any block. Then put in some water & try to spin it out; if the water does not flow out easily you have to look into your pump, could be a block in there. Refer to user's manual.

Kenmore 43052... | Answered on Feb 13, 2008


How long have you had it? Generally, washers won't operate with the lid up for safty reasons. If the lid is down and it doesn't operate, the lid safety interlock may be bad or loose. If visible, try pushing the interlock down with a screwdriver.

Kenmore Washing... | Answered on Sep 09, 2019


then perhaps you need a new control board call local repair services

Kenmore Washing... | Answered on Aug 23, 2019


try checking your dog ears located under the center post cap. they may be worn and jumping teeth

Kenmore Washing... | Answered on Aug 18, 2019


May be high resistance ground in motor or relay. which would be bad news but look for any frayed wires touching the metal cabinet. Hopefully that will be your problem.

Kenmore Washing... | Answered on Aug 18, 2019

Not finding what you are looking for?
Kenmore 43052 Front Load Washer Logo

Popular Tags

36 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Jim Chinnery
Jim Chinnery

Level 1 Expert

10 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Kenmore Washing Machines

Most Popular Question

get loud noise during spin cycle sounds

  • Washing Machines
Loading...